Stage 3 B6 A4 1.8t Dyno #'s Eurodyne 613B6 TUNED!!!!

[iamshayan]

Start off the post by saying Sam (613b6) is the Fucking MAN!

Just left the dyno. Made some good numbers really happy with the results.



Made 320awhp and 330awtq.



build thread :
http://www.audizine.com/forum/showth...ver-read/page3

setup is as follows

@28psi

- Eurodyne maestro 7
- GTRS 2871 Eliminator
- 034 inlet - stock airbox
- ID 72cc Injectors
- Snowperf stg.2 meth (washer fluid)
- TT225 MAF
- 3" catless downpipe (vband + stainless)
- AWE 2" fmic.
- P&P stock exhaust manifold
- Forge dv + MBC
new motor with 120k
- Stock head
- Built bottom end/ rods,piston rings & bearings.

Last years setup was 255awhp and 276wtq
Build thread : http://www.audizine.com/forum/showth...-my-GTRS-Build
@24

- Revo 3 (sps B7, T7, F9)
- GTRS 2563
- EV14 550cc
- 034 inlet
- stock maf
- pte 3" fmic 2"5 piping
- 3" catless down pipe (ghetto fab)
- p&p exhaust manifold
- forgve dv
- stock n75
- Stock motor at 250,000km

(last years pull)


Just wanted to thank sam for all his help with everything, especially the tuning But also for putting up with me and my drama fits. Not to mention my constant thoughts to set the car on fire/sell it.
Been a long summer and it started with a blown motor. Just happy to be where I'm at now.
Plans for next year will probably be cams, SEM intake manifold, New FMIC & Intake, possible HTA internals on the GTRS.

I'd also like to thank you guys for putting up with me and my "whats broken now" threads.

Cheers!

[texasboy21]

Great numbers and powerband!

[Joey0918]

Very nice #'s Wish I could do this on my TIP. Unfortunately it wont hold up to this.

[dougyfresh]

SOLID.

Must be fun on the street.

Congrats!

[Turbavanttro]

Is this among the best numbers yet using a stock intake manifold?

Very impressive! Congrats! You must be quite pleased!

[b6Hate4]

Djdksisnenjew I need rods! Setup looks awesome though Shayan!

[613B6]

Congrats again Shayan for sticking with it and putting in all that hard work and time!

Pleasure working with you :)

[Bische]

Great work!

Lets see some 3rd gear pull times for comparation

[Akronnnnnnnn]

nice numbers shayan! I did not know you were on an eliminator.

[CyberPMG]

Can't watch the vids here at work. What numbers did you put down?

Ah... I see the numbers...

Made 320awhp and 330awtq.

Nice! I wanted to get mine to 300+ at the wheels, but I guess I need to change a few things to make that happen.

[Wet0willy01]

Great work Iam and Sam.

[viceprp]

Must be fun on the streets.

[Operator]

Solid numbers and build!!

[freeloader700]

That would be a blast! nice numbers.

[Don Supreme]

Was your motor failure due to broken rods?

[Matt Devo]

very nice man, really hoping to see something similar out of mine when it's done next month :)

[iamshayan]

Great numbers and powerband!

thank you sir!

Very nice #'s Wish I could do this on my TIP. Unfortunately it wont hold up to this.

Siggiepop just finished doing a 6mt swap, matt devo has done one too, no excuses!

SOLID.

Must be fun on the street.

Congrats!

Thank you sir! It is a blast!

Is this among the best numbers yet using a stock intake manifold?

Very impressive! Congrats! You must be quite pleased!

I think so! thank you, soo happy!

Djdksisnenjew I need rods! Setup looks awesome though Shayan!

do it. do it do it.

Congrats again Shayan for sticking with it and putting in all that hard work and time!

Pleasure working with you :)

couldn't have done it without you <3

Great work!

Lets see some 3rd gear pull times for comparation

thanks!
Going to be working on launch control videos and I'll get some 3rd gear pull videos too :)

nice numbers shayan! I did not know you were on an eliminator.

yep exhaust manifolds are expensive and officers are nosy.

Can't watch the vids here at work. What numbers did you put down?

Ah... I see the numbers...

Nice! I wanted to get mine to 300+ at the wheels, but I guess I need to change a few things to make that happen.

do it, I'm sure sam would be glad to help you out!

Great work Iam and Sam.

Thank you sir, thanks again for the fuel pump!

Must be fun on the streets.

so much!

Solid numbers and build!!

:D

That would be a blast! nice numbers.

:D

Was your motor failure due to broken rods?

lol no it was dying due to age and me beating on it I assume. timing belt tensioner failed and the belt was slapping around, but then randomly the tstat exploded and the car overheated and I couldnt pull over for like 5 miles and I ended up cracking the cylinder head in each cylinder between valves. (already had built motor waiting to go in, no fucks were given)
pics of carnage

very nice man, really hoping to see something similar out of mine when it's done next month :)

couldnt have done it without you sir. thanks for always being there for me too!

[Bische]

thanks!
Going to be working on launch control videos and I'll get some 3rd gear pull videos too :)

A log from a third gear pull is better to derive times from

[CO AVANT]

Nice results!

What were your uncorrected #'s?

[iamshayan]

Damn, shayan those are some awesome numbers. Definitely a fun powerband to play around with on the street!

thank you sir and it is no doubt.

Nice results!

What were your uncorrected #'s?

thank you.
I`m not sure.
run conditions : 72.09F 29.82in-Hg, humidity: 38% STD: 1.01

Oakville is apparently 568ft ASL.

last years condition
86.43F 29.55in-Hg, humidity: 23% STD: 1.03

[Charles.waite]

Damn, shayan those are some awesome numbers. Definitely a fun powerband to play around with on the street!

[Arclight]

Nice work Shayan - hope to see your ride next H2Oi!

[vinny.dtw]

Niiice, numbers buddy! Congrats. Solid setup!

[TheOperation]

Must be nice to have software which actually works properly...................................

[swededA4]

Nice Shayan. Looks like you are getting everything worked out.

[iamshayan]

Nice Shayan. Looks like you are getting everything worked out.

yuss ben its fiinally all coming together!

Must be nice to have software which actually works properly...................................

seems like you have the same mods as me. what numbers are you making with that uni stuff?


heres a short video I made of my car doing squats.

[texasboy21]

^fantastic video! MUST. HAVE. LAUNCH. CONTROL.

[Bische]

Any 3rd gear pull times?