C7 A6/A7 & S6/S& VAG COM list and help

[Packy]

What is VIM on the MMI? I need one of these, but I guess I need a lap top also.

[DVE]

video in motion, means during you are driving video is not disabled

[iBetterDoNow]

Followed instructions and have several wanted features done, but one of them, "Enable Remote Operation Windows and Sunroof", was not working for me. After setting bit 2 to 1, I could only use remote to close by pressing lock button, but not opening them with unlock button. Is there something that I have missed? TIA.

[HyperM3]

Followed instructions and have several wanted features done, but one of them, "Enable Remote Operation Windows and Sunroof", was not working for me. After setting bit 2 to 1, I could only use remote to close by pressing lock button, but not opening them with unlock button. Is there something that I have missed? TIA.

You need to allow the permissions in the MMI.

[iBetterDoNow]

Thank you for your quick response. Another question, does the engine have to be running in addition to ignition turned on to perform "auto scan", for my auto scan reported "Address 03: ABS Brakes --> Cannot be reached"

[HyperM3]

Thank you for your quick response. Another question, does the engine have to be running in addition to ignition turned on to perform "auto scan", for my auto scan reported "Address 03: ABS Brakes --> Cannot be reached"

Not necessarily started but it should be powered up in the accessory position. Obviously the VAG wouldnt be operating if it wasnt powered up correctly. All codes are stored in the ECU whether or not the car is actually started or not.

[iBetterDoNow]

This is my first push-button-to-start car. :) I push the button while my foot is not on the brake. Does this mean that it is on accessory position? Here is a complete list of the auto-scan
Chassis Type: FC (4G0)
Scan: 01 02 03 05 08 09 0E 10 15 16 17 19 28 36 3B 3C 42 44 46 47
52 53 55 56 5F 62 6C 72 8F 90

01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
04-Steering Angle -- Status: OK 0000
05-Acc/Start Auth. -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: OK 0000
0E-Media Player 1 -- Status: OK 0000
10-Park/Steer Assist -- Status: OK 0000
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: OK 0000
28-HVAC, Rear -- Status: OK 0000
33-Flux Capacitor -- Status: Malfunction 0010
36-Seat Mem. Drvr -- Status: OK 0000
3B-Sensor Elect. -- Status: OK 0000
3C-Lane Change -- Status: OK 0000
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: OK 0000
46-Central Conv. -- Status: OK 0000
47-Sound System -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
53-Parking Brake -- Status: OK 0000
55-Xenon Range -- Status: OK 0000
56-Radio -- Status: OK 0000
5F-Information Electr. -- Status: Malfunction 0010
62-Door, Rear Left -- Status: OK 0000
6C-Back-up Cam. -- Status: OK 0000
72-Door, Rear Right -- Status: OK 0000
8F-Pretens. Frt Left -- Status: OK 0000
90-Pretens. Frt Right -- Status: OK 0000

-------------------------------------------------------------------------------
Address 01: Engine (J623-CGXB) Labels: 06E-907-551-CGW.clb
Part No SW: 4G0 907 551 A HW: 4G0 907 551 A
Component: 3.0l V6 TFSIH05 0007
Revision: --H05---
Coding: 0A2A0034052600060000
Shop #: WSC 02311 785 00200
ASAM Dataset: EV_ECM30TFS0214G0907551A 003008
ROD: EV_ECM30TFS0214G0907551A.rod
VCID: 275D1D1E5E4D1926F59-8072

No fault code found.
Readiness: 0000 0000

-------------------------------------------------------------------------------
Address 02: Auto Trans (J217) Labels: 0BK-927-156.clb
Part No SW: 4G0 927 158 E HW: 0BK 927 156 R
Component: 0BK 30TFSIUSA H08 0002
Revision: --H08---
Coding: 001102
Shop #: WSC 02311 785 00200
ASAM Dataset: EV_TCMAL551211 001014
ROD: EV_TCMAL551211_AU48.rod
VCID: 306FF6426B835E9E243-8065

No fault code found.

-------------------------------------------------------------------------------
Address 03: ABS Brakes
Cannot be reached

[soslower]

This is my first push-button-to-start car. :) I push the button while my foot is not on the brake. Does this mean that it is on accessory position? Here is a complete list of the auto-scan
Chassis Type: FC (4G0)
Scan: 01 02 03 05 08 09 0E 10 15 16 17 19 28 36 3B 3C 42 44 46 47
52 53 55 56 5F 62 6C 72 8F 90

01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
04-Steering Angle -- Status: OK 0000
05-Acc/Start Auth. -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: OK 0000
0E-Media Player 1 -- Status: OK 0000
10-Park/Steer Assist -- Status: OK 0000
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: OK 0000
28-HVAC, Rear -- Status: OK 0000
33-Flux Capacitor -- Status: Malfunction 0010
36-Seat Mem. Drvr -- Status: OK 0000
3B-Sensor Elect. -- Status: OK 0000
3C-Lane Change -- Status: OK 0000
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: OK 0000
46-Central Conv. -- Status: OK 0000
47-Sound System -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
53-Parking Brake -- Status: OK 0000
55-Xenon Range -- Status: OK 0000
56-Radio -- Status: OK 0000
5F-Information Electr. -- Status: Malfunction 0010
62-Door, Rear Left -- Status: OK 0000
6C-Back-up Cam. -- Status: OK 0000
72-Door, Rear Right -- Status: OK 0000
8F-Pretens. Frt Left -- Status: OK 0000
90-Pretens. Frt Right -- Status: OK 0000

-------------------------------------------------------------------------------
Address 01: Engine (J623-CGXB) Labels: 06E-907-551-CGW.clb
Part No SW: 4G0 907 551 A HW: 4G0 907 551 A
Component: 3.0l V6 TFSIH05 0007
Revision: --H05---
Coding: 0A2A0034052600060000
Shop #: WSC 02311 785 00200
ASAM Dataset: EV_ECM30TFS0214G0907551A 003008
ROD: EV_ECM30TFS0214G0907551A.rod
VCID: 275D1D1E5E4D1926F59-8072

No fault code found.
Readiness: 0000 0000

-------------------------------------------------------------------------------
Address 02: Auto Trans (J217) Labels: 0BK-927-156.clb
Part No SW: 4G0 927 158 E HW: 0BK 927 156 R
Component: 0BK 30TFSIUSA H08 0002
Revision: --H08---
Coding: 001102
Shop #: WSC 02311 785 00200
ASAM Dataset: EV_TCMAL551211 001014
ROD: EV_TCMAL551211_AU48.rod
VCID: 306FF6426B835E9E243-8065

No fault code found.

-------------------------------------------------------------------------------
Address 03: ABS Brakes
Cannot be reached

Yes! you're ready to have some fun now!

[sciblades]

You should probably get your 33 Flux capacitor checked out!

Sent from my Z10 using Tapatalk 2

[iBetterDoNow]

LOL. I did not know why there was 33 Flux capacitor ? Newer scan did not have that. Got another question: "MMI reset" was mentioned in VIM mod. Is it the same as holding 3 buttons mentioned in the first post in this thread? If it was, is there a special way of pressing them together? I tried a couple of times, but VIM is still not working. TIA.

[Stuke'ite]

So my mom just bought a Premium Plus A6 TDI (and loves it)(I have a 2011 A4 Avant). She has the seat memory but was unaware her Audi would not do something her 2006 Infinity does. When she opens the door the exit the car her infinity the seat slides all the way back, helping her get out of the car and not hit her legs on the steering wheel. With her double knee replacement this is a very nice feature for her. We have learned Audi would only do this if she had the Prestige level, which adds a power tilt steering wheel to the memory seats. The Stealer has old her the only way to get this is to have the Prestige with the wheel. Had she know this she would have just bought the Prestige car to begin with.

Long story longer…can I enable the seat moving back feature in her current car with VAGCOM? I ask because I am sure the dealer will not take her car back and let her order the Prestige car with this feature, even though she has had the car for a week, and driven it only 30 miles.

Thanks for the help!

[hayasa]

I just set one of my memory preset buttons on my S4 to seat all the way back - helps for getting out, cleaning under the seat, etc. I think the wheel position is also linked, so when you press the button, everything should move.

[AudiA6A5]

anyone find / learn more details of all the options in the green menu? I increased my entertainment/music vol (which the bose needed) but haven't tired anything else. Thanks in advance.

[DVE]

I increased my entertainment/music vol (which the bose needed)

You mean the inputgainlevels? Thats help a little bit, but more important is the software update 47A002!

[gatorguy]

I just set one of my memory preset buttons on my S4 to seat all the way back - helps for getting out, cleaning under the seat, etc. I think the wheel position is also linked, so when you press the button, everything should move.

That is genius. Thank you sir!

[gatorguy]

So my mom just bought a Premium Plus A6 TDI (and loves it)(I have a 2011 A4 Avant). She has the seat memory but was unaware her Audi would not do something her 2006 Infinity does. When she opens the door the exit the car her infinity the seat slides all the way back, helping her get out of the car and not hit her legs on the steering wheel. With her double knee replacement this is a very nice feature for her. We have learned Audi would only do this if she had the Prestige level, which adds a power tilt steering wheel to the memory seats. The Stealer has old her the only way to get this is to have the Prestige with the wheel. Had she know this she would have just bought the Prestige car to begin with.

Long story longer…can I enable the seat moving back feature in her current car with VAGCOM? I ask because I am sure the dealer will not take her car back and let her order the Prestige car with this feature, even though she has had the car for a week, and driven it only 30 miles.

Thanks for the help!

Prestige does not have this. The 'easy entry' feature on the prestige only moves the steering wheel up and out. On the A8 it will move the seat all the way back as well move the steering wheel up. I've looked in VCDS for this and it says the module is not installed when I try to adjust it.

As a workaround, I would do what the other poster suggested of programming another memory button to move the seat all the way back.

[/dev/null]

So my mom just bought a Premium Plus A6 TDI (and loves it)(I have a 2011 A4 Avant). She has the seat memory but was unaware her Audi would not do something her 2006 Infinity does. When she opens the door the exit the car her infinity the seat slides all the way back, helping her get out of the car and not hit her legs on the steering wheel. With her double knee replacement this is a very nice feature for her. We have learned Audi would only do this if she had the Prestige level, which adds a power tilt steering wheel to the memory seats. The Stealer has old her the only way to get this is to have the Prestige with the wheel. Had she know this she would have just bought the Prestige car to begin with.

Long story longer…can I enable the seat moving back feature in her current car with VAGCOM? I ask because I am sure the dealer will not take her car back and let her order the Prestige car with this feature, even though she has had the car for a week, and driven it only 30 miles.

Thanks for the help!

Prestige does not have this. The 'easy entry' feature on the prestige only moves the steering wheel up and out. On the A8 it will move the seat all the way back as well move the steering wheel up. I've looked in VCDS for this and it says the module is not installed when I try to adjust it.

As a workaround, I would do what the other poster suggested of programming another memory button to move the seat all the way back.

I just picked up our prestige TDI last week as well, a bit of fooling with the system and I saw that the steering retractor is there, but also would like to see the seat go back too. I have to agree that the simple workaround is posted above, and is typically what my wife and I have done anyway (she is 5' - Im 6'2" so preset #1 is hers, #2 is mine. Our previous Infiniti did this as noted, but I hate the new styling, hence the A6 now.

I haven't done too much with VCDS yet (well a couple things), but will look on my car. Ive got the log file if someone knows what they are looking for (and mine does NOT have the flux capacitor.... that was hilarious!)

[AudiA6A5]

You mean the inputgainlevels? Thats help a little bit, but more important is the software update 47A002!

Yes, and I agree on the update. Did you mess with anything else on the 3-4 pages of stuff?


Sent from my iPad using Tapatalk

[DVE]

Did you mess with anything else on the 3-4 pages of stuff?

Only the volumerangers ...

[AudiA6A5]

Thanks DVE, looks like we need a guide on the rest :) I think moved my max entertainment vol up to ~30. I believe the default was much lower. Next time I'll make sure to bring a notebook.


Sent from my iPad using Tapatalk

[kurupt_hawaiian]

bump

[JB616]

anyone figure out the coding to disable the "after-wipe" of the wiper blades after using the washers?

[moosehead1]

anyone figure out the coding to disable the "after-wipe" of the wiper blades after using the washers?

+1. It would be nice to wipe the after wipe.

[maxhawk]

anyone figure out the coding to disable the "after-wipe" of the wiper blades after using the washers?

http://www.audienthusiasts.com/VagComWipers.html

[DVE]

Its not possible to disable it with coding.

[Hockenheim]

Does "Adjust LED Brightness" change the brightness of the DRL strip on full LED's when the headlights come on?

I noticed my DRL LED strip is super bright, but when I turn on my headlights it dims

[soslower]

Does "Adjust LED Brightness" change the brightness of the DRL strip on full LED's when the headlights come on?

I noticed my DRL LED strip is super bright, but when I turn on my headlights it dims

Mine seems to stay bright.

[HyperM3]

Does "Adjust LED Brightness" change the brightness of the DRL strip on full LED's when the headlights come on?

I noticed my DRL LED strip is super bright, but when I turn on my headlights it dims

Thats the way its supposed to work. However, with the VAG, you can keep the LED lit just as bright if you want so they dont dim when the lights come on. During the day they are at 100% and when the lights come on they dim down to 20%(I believe). I changed mine so they go back up to 80% brightness with the lights on.

[kiku]

Thanks for posting the pic :)



Oh, there's that boost meter in the DIS as well

Can you share how this was enabled?

[Info@EuroCode]

Can you share how this was enabled?

Boost meter is added in with the lap timer.

[kiku]

Boost meter is added in with the lap timer.

Cheers thank you sir

[Pip]

Can you share how this was enabled?

Sorry for the late reply.

Yes the boost meter is enabled together with the lap timer.

When the DIS is in Lap Timer mode, shift your gear stick to manual mode ... there will be a shift bar in the DIS.

Bar fills up ... tells you when to change gear ... :)

[kurupt_hawaiian]

Disable amber corner lights
Disable NAV & Phone warning messages while entering data at speed
Disable Seatbelt Chime
Enable Adaptive brake lights
Enable Hidden menu in MMI
Enable Remote Operation windows&sunroof
Enable VIM on MMI
Adjust LED Brightness

So last night we did the VAG list above and have a little issue we can't figure out. This is for the C7 A6 with the Xenon headlights (not full LEDS). When we have the lights off the LED DRL strip works fine. But as soon as we turn the headlights on the DRL strip goes off and just the Xenon headlight comes on. There's a bulb out error that pops up saying that the DRL's are out...but they still work when you turn the headlight switch back off to run DRLs. We tried putting the codes back to normal (stock) but same issue. Help!

[DVE]

Regarding LED Brightness

What was the default value (26?) and which is the new value?

[kurupt_hawaiian]

Regarding LED Brightness

What was the default value (26?) and which is the new value?

I can't remember the default but we changed it to 100.

[soslower]

I remember I had to change a digit in mine not a checkbox. Mine was flickering also flickering in top of the bulb out error. But it's all working now. Put up a screenshot of your code.

[kurupt_hawaiian]

I remember I had to change a digit in mine not a checkbox. Mine was flickering also flickering in top of the bulb out error. But it's all working now. Put up a screenshot of your code.

That's what I was thinking, can you post your code? I'm gonna go meet up with him again later on today and try to figure this thing out.

[Kamakazi]

Hey Rich its for my car lol ;-)

Sent from my SCH-I605 using Tapatalk

[kurupt_hawaiian]

Okay we got this figured out. If OP wants to put this in the first post for future C7 A6 owners with the Xenon headlights (not full LED), that would be nice.

Adjust brightness for Xenon LED strip (headlights off)
[09 – Cent. Elect.] [Security Access - 16] (enter security code. One of the default codes is- 20113)
[Adaptation - 10] -> Channel 1
Set value to 100 for full brightness

Adjust brightness for Xenon LED strip (headlights/parking lights on)
[09 – Cent. Elect.] [Security Access - 16] (enter security code. One of the default codes is- 20113)
[Adaptation - 10] -> Channel 3
Set value to 100 for full brightness

I had to click the values up to 100. If I just typed in 100 test and save it still wouldn't be as bright. It was really weird. But we got everything worked out.

[sciblades]

Okay we got this figured out. If OP wants to put this in the first post for future C7 A6 owners with the Xenon headlights (not full LED), that would be nice.

Adjust brightness for Xenon LED strip (headlights off)
[09 – Cent. Elect.] [Security Access - 16] (enter security code. One of the default codes is- 20113)
[Adaptation - 10] -> Channel 1
Set value to 100 for full brightness

Adjust brightness for Xenon LED strip (headlights/parking lights on)
[09 – Cent. Elect.] [Security Access - 16] (enter security code. One of the default codes is- 20113)
[Adaptation - 10] -> Channel 3
Set value to 100 for full brightness

I had to click the values up to 100. If I just typed in 100 test and save it still wouldn't be as bright. It was really weird. But we got everything worked out.

Will edit in am thank you

Sent from my Z10 using Tapatalk 2