the RS5 from OZ ...

[marzz]

I have 20x10.5 all around on 295/30... They fit perfectly, but I'm not lowered. I have a friend who wedged 305 in the back of an S5 so it should be no problem on your RS. I would venture to say you could even make 315's work. I know that 325's are available from Michelin in a much smaller overall diameter, so even those might be work-able. Who knows. If anyone can do it, I would pick you.

haha we got to do some try fits ... see what happens
was interested in 315/30/19

[NOFEARCT]

haha we got to do some try fits ... see what happens
was interested in 315/30/19

Front and rear? Or staggered? Haha

[marzz]

Front and rear? Or staggered? Haha

don't think 315 at the front would be too healthy ...

[Not A Good Idea]

don't think 315 at the front would be too healthy ...

looking great so far.
max in the rear would be 11"et25 with a 305. same in the front but your max turning radius will suffer.

[NOFEARCT]

looking great so far.
max in the rear would be 11"et25 with a 305. same in the front but your max turning radius will suffer.

At ride height or lowered?

[Not A Good Idea]

At ride height or lowered?

lowered.

i run 11" with 295 only because im on air. there is literally 1mm space between my fender and rim in the rear. no rub.

http://www.audizine.com/classifieds/...107_082252.jpg

[NOFEARCT]

lowered.

i run 11" with 295 only because im on air. there is literally 1mm space between my fender and rim in the rear. no rub.

http://www.audizine.com/classifieds/...107_082252.jpg

Nice, looks good

[marzz]

lowered.

i run 11" with 295 only because im on air. there is literally 1mm space between my fender and rim in the rear. no rub.

http://www.audizine.com/classifieds/...107_082252.jpg

cheers, the RS5 hubs are thicker then S5 so the offset would have to be different ...

[TheDapperDriver]

Front and rear? Or staggered? Haha

only this guy would do it lmao
i used to have 305's on my old set in the rear

[marzz]

I have 20x10.5 all around on 295/30... They fit perfectly, but I'm not lowered. I have a friend who wedged 305 in the back of an S5 so it should be no problem on your RS. I would venture to say you could even make 315's work. I know that 325's are available from Michelin in a much smaller overall diameter, so even those might be work-able. Who knows. If anyone can do it, I would pick you.

295/30/20 increases the diameter vs stock, how accurate is your speedo if you don't mind me asking?
305, what offset?
the minimum will be 305 but has to work when very low, as this my be the track only setup, so semi or slicks have to be available in that size ...

Honestly, even the 295's are a bit much at times to have in the front. I mean a lowly Veyron only has 265's in the front. I just worry that staggered setups will only contribute to additional under steer.

happy with 275 at the front but thinking of 255-265, understeer not necessary, if you setup your suspension properly, R8 runs staggered as stock ...

only this guy would do it lmao
i used to have 305's on my old set in the rear

305, what offset?

[NOFEARCT]

295/30/20 increases the diameter vs stock, how accurate is your speedo if you don't mind me asking?



happy with 275 at the front but thinking of 255-265, understeer not necessary, if you setup your suspension properly, R8 runs staggered as stock ...

295/30 vs 275/30 is less than a 2% increase in overall diameter, the speedometer for the most part is still pretty accurate.

The Veyron comment on might part was a joke, you can't compare the RS5 with the massive engine way out front to an R8 or a Veyron... Of course those cars run staggered setups but they won't understeer like ours because the engine won't be pulling the car off of the proper line through the corners. Understeer really only occurs when the front tires lose grip before the backs do, putting on smaller tires in the front (relative to the back) won't help that.

[marzz]

in for check up recently ...

[Jsivadas]

Sooooo sexyy!!! Awesome job man!!

in for check up recently ...

[TheDapperDriver]

305, what offset?

was during when i had my concave dpe set, DPE does not reveal their offsets so no clue really

[marzz]

think I'm done with the exhaust, unless something brakes, the initial sound in combination with the SC wine is just awesome , best I've had so far, mind due the Kline setup is bigger in diameter 2.75" vs 2.5" stock, clips to follow when sound settles in ...

[marzz]

Also, received the mid section from Kline to complete the whole system and mellow the sound a little ...