Tri-State Section VAG-COM Owners

[AngryQ5]

Congrats on the Q5. Is that a typo on the price? The RT site shows '09+ Q5 using either Hex-Can-USB or Hex-Com-Can (but you need a serial port). The Hex-Can-USB is $350 though. Maybe I'm reading it wrong but I know I'd be bummed if I waited for my cable to arrive and it was the wrong one.

http://www.ross-tech.com/vag-com/car...ions/q5q7.html

Maybe i ordered the wrong one damn
Thx for letting me know will have to call in on monday to get the right one than

Thx again hahahah seeeee im getting help already !!!! Great !!!

One more question are the programming done with the engine idling? Or just plug with with out engine on? I have the keyless entry thx

[Schadenfreude]

No problem. Plug cable in and turn ignition on but car not running. First time you run the software it will direct you to run a test which creates a file for your vehicle and then you are good to go. With the Long Coding Helper, making changes could not be any easier on the newer cars. Even on the previous gen cars, it's just a matter of adding or subtracting numbers to the code to enable a change. The LCH takes care of much of that for you so some changes are simply ticking/unticking boxes or maybe changing an adaptation value. It's a lot of phone enabling a feature that didn't come with the car. Enjoy!

[shonseb]

For the b8s check out the b8 s4 , there is a sticky the that can tell you all the things you can do for newer models. I also started going through the German forums, but still have a while to go before I can figure out how to code from there

Sent from Tmobile MyTouch 4g

[AngryQ5]

No problem. Plug cable in and turn ignition on but car not running. First time you run the software it will direct you to run a test which creates a file for your vehicle and then you are good to go. With the Long Coding Helper, making changes could not be any easier on the newer cars. Even on the previous gen cars, it's just a matter of adding or subtracting numbers to the code to enable a change. The LCH takes care of much of that for you so some changes are simply ticking/unticking boxes or maybe changing an adaptation value. It's a lot of phone enabling a feature that didn't come with the car. Enjoy!

Thx man !!!!

Just received them today ^^

The right ones and yes they were 350 something well anyways will be trying some things out today....

Thx guys

And if anyone from queens nyc area needs vagged? Pm me hahahah

[AngryQ5]

For the b8s check out the b8 s4 , there is a sticky the that can tell you all the things you can do for newer models. I also started going through the German forums, but still have a while to go before I can figure out how to code from there

Sent from Tmobile MyTouch 4g

Ok will check it out
Iwill go slow on it though scary if i mess things up!!!

[Schadenfreude]

Ok will check it out
Iwill go slow on it though scary if i mess things up!!!

Best instructions are on the first page of the B8 S4 vagcom thread. Print out the codes and as you go along, write down your original coding before you change it. That way if something doesn't seem right or does not work, it is easy to go back and put restore your original coding. Have fun with it

[shonseb]

Ok will check it out
Iwill go slow on it though scary if i mess things up!!!

you'll see, it becomes very easy.

Sent from Tmobile MyTouch 4g

[AngryQ5]

you'll see, it becomes very easy.

Sent from Tmobile MyTouch 4g

Yes I just vagged it lol

The sweep is done

Drl turl signal done

Keyless warning done and will do more soon

I feel like audi geeeeeeeek lol

Thx again guys ^^


Sent from my GT-P3113 using Tapatalk 2

[AngryQ5]

One quick question ....
Can anything serious go wrong ? I plan todo whats only said in the forum no venturing into wilderness just curious and worried thx again

Sent from my GT-P3113 using Tapatalk 2

[AngryQ5]

Ok i was successful in doing some but

I cant seem to get reverse tilt mirror .....
It said to go to byte 4 and change bit 2&4 but all i am able to do is either click or unclick on the check mark?

How do you set value for any "bits"? So confused....

And also hidden menu? Is this something when enabled that show on your nav screen? Or within the vagcom menu? Lol sorry

[Schadenfreude]

Ok i was successful in doing some but

I cant seem to get reverse tilt mirror .....
It said to go to byte 4 and change bit 2&4 but all i am able to do is either click or unclick on the check mark?

How do you set value for any "bits"? So confused....

And also hidden menu? Is this something when enabled that show on your nav screen? Or within the vagcom menu? Lol sorry

Just to verify, when you say "nav" you mean nav and not just the screen. I ask because the hidden menu is nav only (at least on the B8 it is). The hidden menu screen will replace your MMI screen when it comes up. You bring it up by holding both buttons to the left of the MMI controller (Car and Setup I believe) down for about 6 seconds. You exit the screen by resetting the system (you'll have to see what button combo resets the Q5 system, either online or in your manual).

You can navigate the vcds screen with your arrow keys from byte to byte. If there is no check box for the bit, then you can enter the new value manually.

[shonseb]

you have to have the mirror switch on passenger for the reverse tilt to work

[LakeShow]

you have to have the mirror switch on passenger for the reverse tilt to work

+1...it should be standard on 2013 Audi's

[AngryQ5]

Ok i will look into it again today thank you

[AngryQ5]

+1...it should be standard on 2013 Audi's

Ok gotem to work thx ^^

[LI NY A4]

Name: Jason
Model: HEX-USB+CAN
Software: I forget, but can easily DL the latest version.
Location: Lindenhurst, NY
Contact: PM for contact info

I can drive to meet. I will charge, tho. What's the going rate?

[NyRevenge]

Name: Jason
Model: HEX-USB+CAN
Software: I forget, but can easily DL the latest version.
Location: Lindenhurst, NY
Contact: PM for contact info

I can drive to meet. I will charge, tho. What's the going rate?

Let me kno the rate. I got a few things. Wanna get done. In Levittown, Near Hicksville

[LI NY A4]

Let me kno the rate. I got a few things. Wanna get done. In Levittown, Near Hicksville

PM me with what you want done, where you want to meet, etc...
Shoot me an offer on the rate and we can negotiate it.

[nonchalant_Gee]

Sup guys anyone in the Bronx or any other borough want to meet up I can go to you or you come to me. Want to do a few mods and run a few test's. you will be compensated for your time

[Capt. Slow]

+1 to what nonchalant said.

I'm in queens so I can come out to LI or any of the 5 boroughs. 2012 Q5, got the list with all the mods I want done.

[shonseb]

Capt., come to the dubs of queens meet on Thursday around 9p. I'll do them
20th ave in front of boulder creek/target

Sent from my Nexus 4 using Tapatalk 2

[Sandeman]

Can someone take me off the list? I no longer own a cable :/

[Ac101]

Where are the ct vagcomers !

[bmp]

Name: Nick
Model: HEX-USB+CAN
Software: Latest version
Location: Atlantic City,NJ
Contact: PM for contact info

[scottyboyx845]

Can someone help me log my b5 s4? Just looking for typical diagnostics of how the car is running in general. I live in Putnam county but frequent Westchester and could meet up during a lunch break. Shoot me a PM. Thanks In advance.

[DontHait]

Is anyone available in Morris County, NJ? Just want to get some simple coding done.

[funkymillah]

Name: Ronn
Model: HEX-USB+CAN
Software: Latest version
Location: Woodbridge Area,NJ (Middlesex County)
Contact: PM for contact info

[quattroScinque]

Im picking up an 08 S5, want to vagginate it (DRL, brightness, windows, needle sweep, video in motion - standard stuff). Located in North Jersey, Ridgefield, would like to meet with someone who has already done a few. Willing to compensate for your troubles.. Send me a pm, dont really want to go too far from home base.

Looking to do these by next week if possible.

[shonseb]

I don't think you have a DVD player to enable video in motion. Pretty sure you have mmi 2g and not 3g

Sent from my Nexus 4 using Tapatalk 4

[rooski39]

Anyone available in the north jersey/hoboken area for a few vag com adjustments? Much appreciated.

[Lazydog]

Anyone in SE PA willing to VAG my '12 A8L? PM me.

Would like to get the
widows up/down with fob
needle sweep
Video in motion
and I read somewhere about getting the break lights to flash when you when doing an emergency breaking.

[rahip4567]

Model : HEX USB+CAN
Software : VCDS Release 11.11.6
Location : Danbury, CT
Contact : Shoot me a PM or email @ [email protected]

[Sour]

In Brooklyn, Prospect Heights, need to clear a service reminder tomorrow or Thursday if possible. Please let me know. Thanks.

[igotonee]

Anyone in Westchester, NY willing to VAG-COM my '04 Audi S4? PM me.

Would like to get the
Remote Windows
Independent Fogs
needle sweep (if possible)
Increase Rear Taillight, Brake Light, and Fog Light Brightness
& any other that could be done.

[Fir$t_TubE]

anyone near Huntington, LI that could help me VAG-COM my '10 Audi S4?
will provide booze or cash.

PM me if you can help a bro out

[gohan]

central NJ, would like:

widows up/down with fob (i really miss this feature!)
needle sweep

PM me.

[Jaymehaze]

Westchester/Putnam ny
Hex+can USB .. Works on my 11 s5

[Just A B8]

Hex-Can-USB

Bergen County / Near the Garden State Plaza Mall

[gohan]

Just a b8. Hook a brother up!

Sent from my SCH-I605 using Tapatalk 4

[Just A B8]

Just a b8. Hook a brother up!

Sent from my SCH-I605 using Tapatalk 4

PM coming your way sir. I like the teaser pic of your new wheels.