My Software/Hardware Modification List (if the dealer hard resets) - RVC, TV, VIM

[RichTJ99]

Hi,

Here are my notes of my Software/Hardware Modification List (in the event of a dealer hard reset). This includes the setting up of a Rear View Camera, Ipod/TV interface & VIM of the RNSE as well as other software codes (not chipped yet).

If everything gets wiped out, I will have a good list of what & how.

Setup + FM = radio reset.


Vag Codes:


1. Changed Vagcom - Seatbelt code - "Select" "17" Change to: 0023208
2. Changed Vagcom - REMOTE WINDOWS + 1 CLICK LOCKs - "Select" "46" Change to: 11896
3. Look at 09 - headlight (no ambers & brights + fog) - "Select" "9" change to (check first) - "01023" (original) to "01021"

RNS-E Modifications for Rear View Camera

1. Added rear view camera (make sure that under #37, adaption code channel 4 is coded to 1)
2. Rear view camera continued - must be in Lambo mode - change code from 0301637 to 0101637 (not change of first 3 to 1).
3. Also make sure that IMA + is on the TV mode, then hold setup for 4 seconds, on DIS you should see IMA+ menu, press setup until you reach RVC, turn dial

to get to 01 (camera on). RV01
4. IMA+ has 300mAH fuse & is connected to the Sunroof Fuse (#30)

The RVC should be working

RNS-E Modifications for TV/IPOD/ViIM (You will lose all settings & saved data, addresses, etc)

1. Start by getting codes - vag, applications, Controller channels map, controller address 37
2. CSV file will be in C:\Ross-Tech\VCDS-Beta\Logs (or comperable) - SAVE THIS IN ANOTHER LOCATION
3. Now we have all the working codes for Nav (only item effected by this mod)
4. Start by downgrading thes software -Select #37, adaption code channel 97 is coded to 1 (forced downgrade)
5. Insert VIM Euro 0080 (source & dest US)
6. Once upgrade is done (enter PIN if needed), check #37, channel 5, make sure it reads 250 then remove radio fuse for 2 hours.
7. Plug in fuse, power up RNSE (everything should be in german),
8. Insert US0200 disc & let it upgrade
9. Insert "fake" US0270 disc (a 200 disc with the version saying 0270)
10. Insert real US0260 disc (0260 disables the TV option).
11. Ensuring the old channel map is copied elsewhere & renamed, Goto vag, applications, Controller channels map, controller address 37.
12. Compare original channel map with new channel map, make sure that coding matches original map.

Kufatec.de IMA+ TV control / IPOD

1. IMA+ is located on left of RNS, wires going over steering wheel & 5amp fuse is sitting on Garage fuse (need to change this). Fuse 16
2. Also make sure that IMA + is on the TV mode, then hold setup for 4 seconds, on DIS you should see IMA+ menu, press setup until you reach 2C, turn dial to

get to 18 (DLO Homedock). - 2C18.


Thats it for now. More to come!

When bringing to a dealer for service:

1. Change out of Lambo mode - #37 change code from 0101637 to 0301637 - this will disable Lambo mode & RVC
2. Possibly put OEM Ipod shell back in.




My Software/Hardware Modification List (in the event of a dealer hard reset)


Vag Codes:


1. Changed Vagcom - Seatbelt code - "Select" "17" Change to: 0023208
2. Changed Vagcom - REMOTE WINDOWS + 1 CLICK LOCKs - "Select" "46" Change to: 11896
3. Look at 09 - headlight (no ambers & brights + fog) - "Select" "9" change to (check first) - "01023" (original) to "01021"

RNS-E Modifications for Rear View Camera

1. Added rear view camera (make sure that under #37, adaption code channel 4 is coded to 1)
2. Rear view camera continued - must be in Lambo mode - change code from 0301637 to 0101637 (not change of first 3 to 1).
3. Also make sure that IMA + is on the TV mode, then hold setup for 4 seconds, on DIS you should see IMA+ menu, press setup until you reach RVC, turn dial

to get to 01 (camera on). RV01
4. IMA+ has 300mAH fuse & is connected to the Sunroof Fuse (#30)

The RVC should be working

RNS-E Modifications for TV/IPOD/ViIM (You will lose all settings & saved data, addresses, etc)

1. Start by getting codes - vag, applications, Controller channels map, controller address 37
2. CSV file will be in C:\Ross-Tech\VCDS-Beta\Logs (or comperable) - SAVE THIS IN ANOTHER LOCATION
3. Now we have all the working codes for Nav (only item effected by this mod)
4. Start by downgrading thes software -Select #37, adaption code channel 97 is coded to 1 (forced downgrade)
5. Insert VIM Euro 0080 (source & dest US)
6. Once upgrade is done (enter PIN if needed), check #37, channel 5, make sure it reads 250 then remove radio fuse for 2 hours.
7. Plug in fuse, power up RNSE (everything should be in german),
8. Insert US0200 disc & let it upgrade
9. Insert "fake" US0270 disc (a 200 disc with the version saying 0270)
10. Insert real US0260 disc (0260 disables the TV option).
11. Ensuring the old channel map is copied elsewhere & renamed, Goto vag, applications, Controller channels map, controller address 37.
12. Compare original channel map with new channel map, make sure that coding matches original map.

Kufatec.de IMA+ TV control / IPOD

1. IMA+ is located on left of RNS, wires going over steering wheel & 5amp fuse is sitting on Garage fuse (need to change this). Fuse 16
2. Also make sure that IMA + is on the TV mode, then hold setup for 4 seconds, on DIS you should see IMA+ menu, press setup until you reach 2C, turn dial to

get to 18 (DLO Homedock). - 2C18.


Thats it for now. More to come!

When bringing to a dealer for service:

1. Change out of Lambo mode - #37 change code from 0101637 to 0301637 - this will disable Lambo mode & RVC
2. Possibly put OEM Ipod shell back in.




Thanks,
Rich

[audirollin00]

great write up.
I posted this to you on Navplus as well but on which wires go from the IMA harness to the pins on the DLO. i assumed the can H/L but not sure where or which way. Ive been using the remote and Id like to get the internal controls working
Thx

[AudiWxGuy]

Where did you get your rear view camera? How did you install it? And last, does it automatically come in when you go into reverse? Would it do that on a 6MT, if in fact it does automatically come on in reverse.

I think a back-up camera would be awesome. It would make backing into a space a helluva lot faster.

[AudiWxGuy]

Where did you get your rear view camera? How did you install it? And last, does it automatically come in when you go into reverse? Would it do that on a 6MT, if in fact it does automatically come on in reverse.

I think a back-up camera would be awesome. It would make backing into a space a helluva lot faster.

[Sharkfin]

lots of double posts^^^^

anyways, thanks for the codes rich!

[RichTJ99]

great write up.
I posted this to you on Navplus as well but on which wires go from the IMA harness to the pins on the DLO. i assumed the can H/L but not sure where or which way. Ive been using the remote and Id like to get the internal controls working
Thx

Hi,

You need to buy this:

http://www.kufatec.de/shop/product_info.php/info/p1048_IMA-Steuerleitung-HomeDock-Deluxe-DLO-individuell.html

Then solder it as described here:

http://www.kufatec.de/infocenter/anleitungen/9.%20IMA%20Multimedia/HomeDock_english.pdf

Look on Page 1 (according to the pdf) for some photos.

The other end gets plugged into the IMA cable (the two prong cable on the left side (2nd).

Or if you dont want to buy the cable, you could take any cable, solder it to the two connections, then attach them to the Kufatec cable (check it before soldering).

Dont touch Can Hi & Lo (for this portion of the install).

http://www.kufatec.de/shop/images/product_images/popup_images/874_0.JPG

[RichTJ99]

Where did you get your rear view camera? How did you install it? And last, does it automatically come in when you go into reverse? Would it do that on a 6MT, if in fact it does automatically come on in reverse.

I think a back-up camera would be awesome. It would make backing into a space a helluva lot faster.

It does automatically switch to camera when in reverse & back. (You will need an IMA+ - see below).


Parts List OEM
I got my camera from here:

http://www.genuineaudiparts.com/

These are all the OEM parts (if you want the OEM Audi camera - very slick setup):

4L0 980 551 - Rear View Camera
4L0 827 574 3F2 - Door handle
4L0 980 553 - Camera retaining clip
N 909 159 01 - Screw

Punch those all in (without spaces) to get pricing. Craig was the cheapest by far with any OEM parts (shows the MSRP & their own price).

Shop around but i think you will find his prices are the best.

Parts List Kufatec


35542 - Wiring harness for IMA Audi RNS E "Basic" / "Basic-Plus"
(http://www.kufatec.de/shop/product_info.php/info/p874_Wiring-harness-for-IMA-Audi-RNS-E--Basic-----Basic-Plus-.html)35676 - Wiring IMA auto switch Rear View Cam Audi RNS-E
(http://www.kufatec.de/shop/product_info.php/info/p973_wiring-IMA-auto-switch-Rear-View-Cam-Audi-RNS-E.html)35538 - IMA Integrated Multimedia Adapter mit Steuerung "Basic-Plus" (http://www.kufatec.de/shop/product_info.php/info/p870_IMA-Multimedia-Adapter-mit-Steuerung--Basic-Plus-.html)
36136 - connection kit original rear view camera VAG to IMA
(http://www.kufatec.de/shop/product_info.php/info/p1029_connection-kit-original-rear-view-camera-VAG-to-IMA.html)


Other suggestion

If you have an Ipod, get a home dock & this cable

http://www.kufatec.de/shop/product_info.php/info/p1048_IMA-Steuerleitung-HomeDock-Deluxe-DLO-individuell.html

Then you can watch movies on your RNSE & control it all from the RNS.

This was very easy to do & came out great. It wasnt the cheapest mod, but by doing it myself, I will know how to fix it if there is an issue.

Also the shipping is FEDEX only from Germany for the Kufatec parts but it was 100% plug & play.

I almost didnt do the Homedock & that would have been a huge mistake as it makes the whole project cost less (its expensive for a rear view camera alone but a rear view camera + Movies its cheap :)

Writeup

http://www.navplus.us/forums/showthread.php?t=8541


If you have any questions, I would be glad to help.

Thanks,
Rich

[acidrome]

Great write up [up]