WTB Coil overs assembled

[bmwpower603]

WTB b5 s4 coil overs.

Preferably assembled with rear shock mount, and front shock mounts.

PM please

-Cheers

[Silverex]

I have a set of BCs I’ll be pulling off my car in next few weeks. Won’t come with rear strut mounts tho.

Springs have some rust and could probably use replacing, and they have been on car for years but still do the job and I would sell for 200+ actual shipping cost which I’d assume would be a lot. Lol.

Replacing for a spring/strut combo since the BCs are alil too low for me. At highest setting they are around 24.5-25” FTG

[bmwpower603]

The bcs are to low, even on highest setting ?

[Silverex]

For me yes highest I can get them is right around 25” FTG and I’d like to be alil higher since it’s my DD

They were on the car when I bought it but pretty sure it’s their regular and not the “low” ones either.

[bmwpower603]

Do you have any pictures?

I’m planning to mount c5 rs6 wheels on my b5. I do NOT want to have to roll/ alter the front fenders.

So I need to leave a little gap in the front

[Quattro 13]

Oh, wow, I had no idea they topped-out so low! I was actually planning on buying a set of BC's later this year since FCP sells (and therefore warranties) them; but I personally feel anything lower than what I like to call "Porsche GT3 ride height" looks like absolute garbage, and if memory serves correctly that's about 25.5"-26" ftg on these cars. So apparently I need to go with a different brand.

Also, any idea what springs you'll be going with? I always figured I would have to go with coilovers to obtain that "OEM+" look I am going for. My black S4 had H&R Sports on it when I bought it, and it made it look like the car was carrying a 12,000 lb payload, with the top of the tires starting to poke up into the wheel well.

[bmwpower603]

Looks like I’ll be starting with some raceland classic coil overs. It’s only a minimum of 1” drop. The bC’s are probably closer to 2” minimum ?

[Silverex]

Do you have any pictures?

I’m planning to mount c5 rs6 wheels on my b5. I do NOT want to have to roll/ alter the front fenders.

So I need to leave a little gap in the front

Here you go, car is filthy tho.






Got a eibach/bilstein combo to replace them. Can post pics of them installed in a few weeks.

[bmwpower603]

PM sent. Did you buy that avant in New Hampshire?

[Silverex]

No last 2 owners were in NJ

[jebbrah113]

Here you go, car is filthy tho.






Got a eibach/bilstein combo to replace them. Can post pics of them installed in a few weeks.

So on your car did you have a set height for the the spring perch or how did you make sure the coil overs were All the same height. I want my car at that height


Sent from my iPhone using Audizine Forum

[Silverex]

So on your car did you have a set height for the the spring perch or how did you make sure the coil overs were All the same height. I want my car at that height


Sent from my iPhone using Audizine Forum

Set them as close as I could, lower car, move a couple feet for everything to settle, measure, then adjust as needed. Probably did that about 4x to get everything with a 1/16”. Kinda annoying cause adjusting one corner can/does affect the opposite corner so have to keep that in mind.

[alpine4]

I will have a set of H&R coilovers for Avant for sale at the end of the month. Gonna sell them at good price.

[cu52]

I'll have a set of rear strut mounts for sale in the next few days, as well as a set of Eibach/MTM springs.

[RMode]

Depending on your timetable, I'll have the Eibach coilovers currently on my car (I purchased them new), with the front and rear mounts, for sale, and they will be inexpensive. Fronts definitely need some freshening (I've put 45k miles on them). Includes the wrenches, collars all spin fine as they should. I'm getting something new.

[CLAY]

I have these available. 5k miles on the coils , they're STs , Pm me if you're interested. I can include the upper rear mounts and front top hats. For extra. 20190515_125739.jpg

Sent from my SM-S906U using Audizine Forum mobile app