Official B8.5 allroad Wheel Thread! Information, Inspiration & Ideas

[Wagoon]

I wanna run these on coils should I go down to 9.5 to avoid rubbing a little bit? or you think 10.5 is fine

Id say 20x10 et30, should be a safe play. Going 9.5 just wont look right. Just remember the Pilot Super Sports are super Chunky. I've since switch to 255/35 Pirelli P-Zeroes, and they fit much nicer.

[fyp0506]

Id say 20x10 et30, should be a safe play. Going 9.5 just wont look right. Just remember the Pilot Super Sports are super Chunky. I've since switch to 255/35 Pirelli P-Zeroes, and they fit much nicer.

thanks for the advice! I'll talk to my bbs dealer and see what they have

[Unit1Evangelion]

- ADV1-15 M2
- 20x10.5 ET:23
- Michelin PSS 275/30/20
- Only if I wanted to rub
- Accuair. My balls touched the ground.



- Hartmann RS6 Replicas
- 20x9 ET: 29
- Toyo Extrema 255/35/20
- 20mm H&R spacers(if I remember correctly)
- Accuair. Car queefed a lot.



- Stock
- Stock
- Perelli P-Zero
- Stock
- God damn it. Stock.

Only pic I have of the new one.

[moose_it]

wheels Bola B8R 8,5x19et26 (quite similar to Ispiri ISR10) tyres 245/40r19, no spacers

[Comfy Pursuit]

Matte graphite Vossen VFS1’s in a 20x9 et25 66.6 5x112
IMG_0723.JPG

[happy2B5]

Those looked great...

[Allthea]

What are people's thoughts on running staggered offsets on an allroad?

[happy2B5]

Staggered offsets only, not widths? Regardless, only drawback to stagger offsets I can see is be prepared to mount/dismount every time you want to rotate tires.

[Adams-Allroad]

Hello

Anyone know where XM Sirius module in installed.

Second question
Navigation unit have gps antenna, 0 satellites.

[Comfy Pursuit]

Hello

Anyone know where XM Sirius module in installed.

Second question
Navigation unit have gps antenna, 0 satellites.

Try your question here, this is specific to wheels and will likely get a better response from the megathread:
B8.5 allroad Info & Resources Megathread
https://www.audizine.com/forum/showthread.php?t=655560

[B6_Dolphin]

2015 AR Premium Plus

- Audi S7 Black Optic Wheel Option
- 20"x 9" ET37
- 265/35ZR20 Yokohoma Advan Sport V103S
- No spacers
- Stock height & suspension

Attachment 114841Attachment 114842

[Allthea]

I put on a set of 19x9.5 BBS Ti CH-R et35 with Conti DWS06 255/35. These will be my winter wheels, but my summers need some work done so I'm riding these for now until they're ready.

They came with the all season tires on them, almost full life. I will probably run a beefier tire when I eventually switch to winter tires; these came from someone with a B8.5 S4.

This is with the rear full of my OEM wheels. Still working on ride height. I can tinker with it since it's on air. I might also put on 10mm spacers to move them out a little




Bagged out:




Profile shot:

[tmodler]

2015 Allroad. Have some 18x9.5 ET24 around. Planning to mount them with some beafy tires.

275/40R18? I think it will fit? Stock ride height. I use this as a real mountain car, so I want a real tire.

Thanks.

C.

P.S. Car is not in Indiana.

[darbyfam]

I run a 255/40 on mine. I think a 275/40 would be a bit tall.

[Allthea]

Use willtheyfit.com and put in your current wheel / tire and the new. It will at least give you an idea of size relative to your current setup

[tmodler]

275/40R18 is the same diameter as the 245/45R18 that were stock. I think at ET 33 I am find outside (fenders) but i’m Not creative or flexible enough to figure out how to measure the innner wheel well dims without just buying a tire and testing it?

Willtheyfit is cool. Thanks.

C.

[Allthea]

I thought you said your wheels were et24?

I just compared your setup to mine: 20x10.5 et30 with 275/30 tires ... mine fits and yours is within the bounds of mine (both et24 and et33, whichever is correct).

I poke further and I am closer to the inner fender and mine fits fine. I am running -2deg camber front and rear, but I'm also lowered on air. At stock height I think you'd be fine. Possibly some rub on the outer fender over VERY large bumps, without camber. You can add camber to the rear with the stock suspension. You need to upgrade control arms in front to get camber in front.

[Insperatus]

Most likely going to get hate from this but here goes... 235/65/R17 Et15 on 1off Rotiforms for this build:





It is still in the testing phase and I can't give out exact suspension specs yet. I know I will get lots of worries on what's going to break, but that's part of it doing it first I guess.

[Comfy Pursuit]

Most likely going to get hate from this but here goes... 235/65/R17 Et15 on 1off Rotiforms for this build:





It is still in the testing phase and I can't give out exact suspension specs yet. I know I will get lots of worries on what's going to break, but that's part of it doing it first I guess.

Bravo! Now we need some #usingit shots of this beast. Is there a build thread for it?

[Insperatus]

Bravo! Now we need some #usingit shots of this beast. Is there a build thread for it?

I do not have a build thread on audizine, but I do have an ig build account. @dffrent_allroad

[Allthea]

Looks awesome. Also kinda looks like your tires are almost contacting the flares already, though.

[kevlarcupid]

@Insperatus That's fly. Wow.

[Insperatus]

Looks awesome. Also kinda looks like your tires are almost contacting the flares already, though.

Had to cut and modify the front inner wheel wall in the rear. It has about 0.5 clearance and towards the bumper about 0.8in clearance. Fronts clear all around no problem.

[Allthea]

Nice. Yeah it's probably just the angle of the shot. I like you're going the utility side of the car. Makes me want to have one of each... lifted and lowered haha

[alhutch]

Most likely going to get hate from this but here goes... 235/65/R17 Et15 on 1off Rotiforms for this build:





It is still in the testing phase and I can't give out exact suspension specs yet. I know I will get lots of worries on what's going to break, but that's part of it doing it first I guess.

I love it! Even on stock size tires, it's a tight fit on the rears (especially the leading edge).

[Insperatus]

Nice. Yeah it's probably just the angle of the shot. I like you're going the utility side of the car. Makes me want to have one of each... lifted and lowered haha

tbh it is pretty close, I haven't had any rubbing yet. AWD systems seem stable so far, I am worried about my gearboxes overheating with the new wheel weights though. Need to upgrade or fab my Tie Rods to have more articulation as that is limiting me on suspension travel.

[Insperatus]

I love it! Even on stock size tires, it's a tight fit on the rears (especially the leading edge).

HAHAH yeah, I will definitely need to modify it some more in the rears. Although I want the body stock looking as possible.

[heyitzalex]

Just put on these 20” OEM RS5 rotors dropped on h&r coils IMG_0823.JPG


Sent from my iPhone using Audizine

[base14]

Just put on these 20” OEM RS5 rotors dropped on h&r coils IMG_0823.JPG
Looks great! What’s your FTG at, and any spacers?

Sent from my iPhone using Audizine

Sent from my iPhone using Audizine

[chip_]

Just put on these 20” OEM RS5 rotors dropped on h&r coils IMG_0823.JPG


Sent from my iPhone using Audizine

Looks good - my new tires and Rotors going on the car today.

[Danaldson]

There really is no better wheel for the all road than the Rs5 Rotors. Im sorta half regretting the wheels purchased. I like them but the rotors are just too good. They will be my next set on the car forsure.

20x10 et35 Rotiform LASR in Candy Red

[darbyfam]

I was going for a more smooth ride with my rim/tire choice. The streets of New Orleans are infamously horrible and I already have two other cars with low profile tires (2015 S3 with 245/35/19 and 2010 TTS with 245/35/19)

I went with a 19 X 9.5" AG with a 255/40/19 Continental tire. Chose the little bit larger sidewall to gain a little more "cush". I couldn't be more happy with the setup for daily driving. Super smooth on the interstate and tolerant of the potholes and cracks on side streets.



Fender measurement is 26.75 with ST Coilovers.

[oatzel]

Just put on these 20” OEM RS5 rotors dropped on h&r coils IMG_0823.JPG


Sent from my iPhone using Audizine

What size tires? I'm on 275/30 but debating on 255/35 or 265/30 when I replace them to hopefully avoid the slight rubbing I get from time to time


Sent from my iPhone using Tapatalk

[dropshadow]

20x10 et35 Rotiform LASR in Candy Red

I love this look. Sometimes I wish I had a car color that could pull off less common wheel colors.

[Danaldson]

I love this look. Sometimes I wish I had a car color that could pull off less common wheel colors.

Thanks! sometimes i wish with something a little more subtle, but its fun having the bright wheels.

[johndingk2]

Sent from my iPhone using Tapatalk

MAN! That looks perfect. what springs are you running or are those coilovers? And wheel and tire size please? I just bought a 2013 with 23k miles. Can't wait to get it looking similar to yours

[BMC2U]

MAN! That looks perfect. what springs are you running or are those coilovers? And wheel and tire size please? I just bought a 2013 with 23k miles. Can't wait to get it looking similar to yours

At that time I had AST springs. Now I’m on KW V1 coilovers. 275/35-20 Toyo Proxes Plus 4s 20x10.5 HRE FF01s


Sent from my iPhone using Tapatalk

[kevlarcupid]

@BMC2U Happy with the v1s? I’m debating v1 versus v2.

[BMC2U]

@BMC2U Happy with the v1s? I’m debating v1 versus v2.

Very happy. I love the way my car drives. I did have to use the S4 springs in the rear. The Avant springs were too soft for my liking. I wouldn’t get the v2s. I’d go straight to v3s if you want adjustment. Keep in mind that you will have to drill a hole in the strut tower for the adjuster knob. If I were tracking the car I’d go with the V3s. For street use, V1s are perfect.


Sent from my iPhone using Tapatalk

[kevlarcupid]

Very happy. I love the way my car drives. I did have to use the S4 springs in the rear. The Avant springs were too soft for my liking. I wouldn’t get the v2s. I’d go straight to v3s if you want adjustment. Keep in mind that you will have to drill a hole in the strut tower for the adjuster knob. If I were tracking the car I’d go with the V3s. For street use, V1s are perfect.

Good advice. I plan to Autocross and occasionally track the car, so I’ll continue to debate the v3s.