NEW: VagCom VCDS Mod List for C7-C7.5

[Dasquade]

I think I figured it out. For me it appeared to require 2 separate steps. I changed channel 98 from a 1 to a 0 (in the 46 Convenience Module) and then I also went into "Adaptation", "Long Coding Helper" and then went to Byte 15. I changed the 5th digit over from the left from a 0 to a 1. So, I now have 00001111 in Byte 15.

I'm not sure where in the long coding that the change to channel 98 was made. I was thinking that I would also see that reflected in Byte 15 but I kept changing channel 98 from 0 to 1 and then back to 0 while checking Byte 15 in the long coding and I did not see anything being updated when I made the change each time. So, it is changing something but its not in there.


All I know is that I now have peace and quiet when I open my door.....both with the engine off and when the engine is running (both while in park). It does still beep when you take the car out of park with the car running; which is actually important to me because I don't want to be driving down the road and my door is not closed properly. So....it's perfect. Thanks to the OP who posted this update.

Hope this helps and was not confusing.

First of all, my bad i didn't replied but i don't have vcds (anymore) and not so familiar with it. Did all my changes with obd11.
Fact is...channel 98 is done in (adaptation (10)' and the byte 15 bite 3 is done in 'coding (07)' if not mistaken.
Good to hear we still get the beep with door open if you set gear from P into N or gears, witch is a warning is a must and accepted :p.

[akingzkid]

First of all, my bad i didn't replied but i don't have vcds (anymore) and not so familiar with it. Did all my changes with obd11.
Fact is...channel 98 is done in (adaptation (10)' and the byte 15 bite 3 is done in 'coding (07)' if not mistaken.
Good to hear we still get the beep with door open if you set gear from P into N or gears, witch is a warning is a must and accepted :p.

It's all good. I didn't expect you to reply that quickly.....especially being on the other side of the world. LOL. I'm just glad I figured it out. And I have video for proof if anyone needs to see it!! LOL. Take care.

[Dasquade]

....And I have video for proof if anyone needs to see it!! LOL. Take care.

Meh no need to see it...what i do not EVER want to see or hear again is somebody making an interior video with a freaking beep beep beep noise on the background because they didn't knew you do can remove it (or just gave up pressing the steeringwheel button to shut it up) :p.

[akingzkid]

Meh no need to see it...what i do not EVER want to see or hear again is somebody making an interior video with a freaking beep beep beep noise on the background because they didn't knew you do can remove it (or just gave up pressing the steeringwheel button to shut it up) :p.

I feel you on that one my brother!!! LOL.

[Gunmeister]

I think I figured it out. For me it appeared to require 2 separate steps. I changed channel 98 from a 1 to a 0 (in the 46 Convenience Module) and then I also went into "Adaptation", "Long Coding Helper" and then went to Byte 15. I changed the 5th digit over from the left from a 0 to a 1. So, I now have 00001111 in Byte 15.

I'm not sure where in the long coding that the change to channel 98 was made. I was thinking that I would also see that reflected in Byte 15 but I kept changing channel 98 from 0 to 1 and then back to 0 while checking Byte 15 in the long coding and I did not see anything being updated when I made the change each time. So, it is changing something but its not in there.


All I know is that I now have peace and quiet when I open my door.....both with the engine off and when the engine is running (both while in park). It does still beep when you take the car out of park with the car running; which is actually important to me because I don't want to be driving down the road and my door is not closed properly. So....it's perfect. Thanks to the OP who posted this update.

Hope this helps and was not confusing.

I think I figured it out. For me it appeared to require 2 separate steps. I changed channel 98 from a 1 to a 0 (in the 46 Convenience Module) and then I also went into "Adaptation", "Long Coding Helper" and then went to Byte 15. I changed the 5th digit over from the left from a 0 to a 1. So, I now have 00001111 in Byte 15.

I'm not sure where in the long coding that the change to channel 98 was made. I was thinking that I would also see that reflected in Byte 15 but I kept changing channel 98 from 0 to 1 and then back to 0 while checking Byte 15 in the long coding and I did not see anything being updated when I made the change each time. So, it is changing something but its not in there.


All I know is that I now have peace and quiet when I open my door.....both with the engine off and when the engine is running (both while in park). It does still beep when you take the car out of park with the car running; which is actually important to me because I don't want to be driving down the road and my door is not closed properly. So....it's perfect. Thanks to the OP who posted this update.

Hope this helps and was not confusing.

I dunno if anyone has tried this on a C7.5 but I tried it earlier today with OBDeleven and changing channel 98 from 1 to a 0 silenced the beep if the ignition is on and the door is open. The beep noise still happens if car is on and door is open though.

Byte 15 for long coding I could not get bit 3 to turn on. Kept saying something went wrong. Maybe someone else with a C7.5 can give it a try and see if they get the same result?

2016 A6 TDI*|*Mugello Blue, Pearl Effect Exterior | Alabastar White Interior | Audi Exclusive Line | Eucalyptus Natural Wood Decorative Inlays | Prestige Package | Comfort Seating Package | Driver Assistance Package | S Line Sport Package | 20" Black Optic Package | Cold Weather Package | Audi All Weather Mats*| 18% Ceramic Film Windows | 70% Ceramic Film Windshield | Thinkware F800 Pro Dash Cam | iDatastart VWX CMVWXA0 Remote Start*| Auto Hold Activated | ESCORT Radar Max 360c*| 1 of 1 for 2016

[back13a6]

I've tried turning off the beep when driver door is open like several of you have, when I go to channel 98 it says "not available". I can make all the other changes no problem, but I still have the annoying beep when my driver door is open. I have a 2013 a6 in north america. I see a few of you are here in the states. Any help would be great.

[TechSavvy]

No problem :) one annoying thing less.
Speaking off, anybody knows how we can set the volume of the radio/media muted or at level 1 after restarting ignition/engine on?
If you mute it before you shut down the car it will still always again be on when you restart the car. Putting it on lowest level (1), after restart it will be on a minimum level again (but still too loud for my likings). Basicly i want the media to be silenced when i enter the car so i can enjoy my engine....

I tried adjusting it in the green menu in the past, forgot what setting, i could adjust it and restart the mmi but it never adjust to the new settings :(.
Also, how can we modify the 'fast lane change' blinks? Again forgot what setting it was but you can adjust, sadely on this car we can set it higher then 3 blinks. Some more recent cars allow you to bump it up to 5.

Did you find a solution to the volume item here? I'm literally on the verge of creating a new thread asking how the F to change 2 items with regard to this - 1) how to keep the volume at whatever it last was at before the vehicle was turned off, and 2) how to disable the fact that when you first start your car and the audio turns on, if you immediately hit the mute knob, it just unmutes it again after like 10 seconds. Drives me absolutely crazy, has done it on every Audi I've had.

[Dasquade]

Did you find a solution to the volume item here? I'm literally on the verge of creating a new thread asking how the F to change 2 items with regard to this - 1) how to keep the volume at whatever it last was at before the vehicle was turned off, and 2) how to disable the fact that when you first start your car and the audio turns on, if you immediately hit the mute knob, it just unmutes it again after like 10 seconds. Drives me absolutely crazy, has done it on every Audi I've had.

no i didn't yet :( . Like said, normally you can adjust it in the green hidden menu but for some reason it doesn't work...

[Audisthesia]

I've tried turning off the beep when driver door is open like several of you have, when I go to channel 98 it says "not available". I can make all the other changes no problem, but I still have the annoying beep when my driver door is open. I have a 2013 a6 in north america. I see a few of you are here in the states. Any help would be great.

Scrrenshot of the issue?

[Dasquade]

Normally the door beep fix should work on both facelift and pre-facelift. I did it on my pre facelift with obd11, not sure if obd11 gives issues on the facelift (friend who sended it too me did it with vcds on his facelift).
Shouldn't mather i think, but did you have the door closed and only ignition on when you did the hack? Shouldn't mather i think, but never know.

[Gunmeister]

Normally the door beep fix should work on both facelift and pre-facelift. I did it on my pre facelift with obd11, not sure if obd11 gives issues on the facelift (friend who sended it too me did it with vcds on his facelift).
Shouldn't mather i think, but did you have the door closed and only ignition on when you did the hack? Shouldn't mather i think, but never know.

Are you talking to me? If so yes I had the door closed and ignition on. I have VCDS too. I'll reverse what I did with OBDeleven and try it with VCDS instead.

2016 A6 TDI*|*Mugello Blue, Pearl Effect Exterior | Alabastar White Interior | Audi Exclusive Line | Eucalyptus Natural Wood Decorative Inlays | Prestige Package | Comfort Seating Package | Driver Assistance Package | S Line Sport Package | 20" Black Optic Package | Cold Weather Package | Audi All Weather Mats*| 18% Ceramic Film Windows | 70% Ceramic Film Windshield | Thinkware F800 Pro Dash Cam | iDatastart VWX CMVWXA0 Remote Start*| Auto Hold Activated | ESCORT Radar Max 360c*| 1 of 1 for 2016

[Carl0s]

I've tried turning off the beep when driver door is open like several of you have, when I go to channel 98 it says "not available". I can make all the other changes no problem, but I still have the annoying beep when my driver door is open. I have a 2013 a6 in north america. I see a few of you are here in the states. Any help would be great.

I had similar issue but then i read Dasquades instructions: "channel 98 is done in (adaptation (10)' and the byte 15 bite 3 is done in 'coding (07)' if not mistaken" That made it work for me. The beep was gone, but it also did something else: Usually, when i stop engine goes to "ready", when i unbuckle, it goes to "off". Then i can get out of the car and lock the doors witch shuts down everything. Now when i try to lock the doors, nothing happens. I need to remeber to manually shut down the car like some neandethral... I tried to to change the adaptation 98 back to 1 and when i tested it on the parking lot, it seemed to work. Then i drove back to home, and the beep was back... whit added bonus that my interior lights no longer work. I guess i need to dig deaper tomorrow.

Another matter: Has anyone of you got the "Automatic parking brake on P" to work? I tried enabling it, but only way it works is if i have the audi autohold enabled. Would love to have it work like the title says - when selector is at P it activates.

And last: Is there any way to reset the car back to factory settings? Just found out that the History function in OBDeleven does not track coding/adaptations...*facepalm* Got error "02874 No signal from comfort module 2" in central electrics and "U111100 - Function limitation due missing message" in airconditioning that i cant get rid of...

[Dasquade]

I had similar issue but then i read Dasquades instructions: "channel 98 is done in (adaptation (10)' and the byte 15 bite 3 is done in 'coding (07)' if not mistaken" That made it work for me. The beep was gone, but it also did something else: Usually, when i stop engine goes to "ready", when i unbuckle, it goes to "off". Then i can get out of the car and lock the doors witch shuts down everything. Now when i try to lock the doors, nothing happens. I need to remeber to manually shut down the car like some neandethral... I tried to to change the adaptation 98 back to 1 and when i tested it on the parking lot, it seemed to work. Then i drove back to home, and the beep was back... whit added bonus that my interior lights no longer work. I guess i need to dig deaper tomorrow.

Another matter: Has anyone of you got the "Automatic parking brake on P" to work? I tried enabling it, but only way it works is if i have the audi autohold enabled. Would love to have it work like the title says - when selector is at P it activates.

And last: Is there any way to reset the car back to factory settings? Just found out that the History function in OBDeleven does not track coding/adaptations...*facepalm* Got error "02874 No signal from comfort module 2" in central electrics and "U111100 - Function limitation due missing message" in airconditioning that i cant get rid of...

Hmm isn't the engine 'ready' dashboard feature not an (facelift) RS feature? That could indeed gives an issue compaired to the (prefacelift) S that doesn't have it. Still unclear what byte 15 bite 1 does (i couldn't change it), maybe that needs to switched aswell in the 'ready' featuring displays?

As for the parkingbrake, don't you not always leave the auto hold enabled (normally it should save it's last action: enabled/disabled after reignition), so switching to P should always automaticly turn on the parking brake (at least it does here).

[Carl0s]

Hmm isn't the engine 'ready' dashboard feature not an (facelift) RS feature? That could indeed gives an issue compaired to the (prefacelift) S that doesn't have it. Still unclear what byte 15 bite 1 does (i couldn't change it), maybe that needs to switched aswell in the 'ready' featuring displays?

As for the parkingbrake, don't you not always leave the auto hold enabled (normally it should save it's last action: enabled/disabled after reignition), so switching to P should always automaticly turn on the parking brake (at least it does here).

Could be, what's confusing is the fact that after doing the programming it worked (tho cant remember if the interior lights worked since it was not dark yet). Then drove 20mins home from the store. When i was emptying the trunk i noticed that the lights are off even tho the switch is in door position. When i restarted the car to move it to my parking spot, i tested the beep and it was back. But i try to do some testing tomorrow and report back.

I hate the way auto hold works with start stop - the delay when i'm starting to press gas and before it actually starts is so long, that the gas pedal has travelled enought causing the take offs to be unnecessary "sporty"... I like much more the behavior where engine starts when you lift your foot from the brake :)

[Dasquade]

Could be, what's confusing is the fact that after doing the programming it worked (tho cant remember if the interior lights worked since it was not dark yet). Then drove 20mins home from the store. When i was emptying the trunk i noticed that the lights are off even tho the switch is in door position. When i restarted the car to move it to my parking spot, i tested the beep and it was back. But i try to do some testing tomorrow and report back.

I hate the way auto hold works with start stop - the delay when i'm starting to press gas and before it actually starts is so long, that the gas pedal has travelled enought causing the take offs to be unnecessary "sporty"... I like much more the behavior where engine starts when you lift your foot from the brake :)

Ah yeah well who uses start/stop anyway :p.
*just stepped in my car. with door open..what a joy now, no beeps no radio volume

[Audisthesia]

I think I figured it out. For me it appeared to require 2 separate steps. I changed channel 98 from a 1 to a 0 (in the 46 Convenience Module) and then I also went into "Adaptation", "Long Coding Helper" and then went to Byte 15. I changed the 5th digit over from the left from a 0 to a 1. So, I now have 00001111 in Byte 15.

I'm not sure where in the long coding that the change to channel 98 was made. I was thinking that I would also see that reflected in Byte 15 but I kept changing channel 98 from 0 to 1 and then back to 0 while checking Byte 15 in the long coding and I did not see anything being updated when I made the change each time. So, it is changing something but its not in there.


All I know is that I now have peace and quiet when I open my door.....both with the engine off and when the engine is running (both while in park). It does still beep when you take the car out of park with the car running; which is actually important to me because I don't want to be driving down the road and my door is not closed properly. So....it's perfect. Thanks to the OP who posted this update.

Hope this helps and was not confusing.

Makes sense. Did channel 98 to 0 and it turns chime off when ignition is on and door is open. But if engine is on, chime is there. So the engine on chime with door open must correspond to Byte 15 in long coding.

Ah yeah well who uses start/stop anyway :p.
*just stepped in my car. with door open..what a joy now, no beeps no radio volume

Did I miss the no radio volume mod somewhere?

[Audisthesia]

[Select] [46 - Central ConvElec.]
Coding
Long Coding Helper
Byte 15
Bit 3, Set New value: 1



Please note, you count the bits from RIGHT to LEFT starting with 0. So bit 3 is fourth position from right as shown in the image:

[esemes]

i have changed my doorchime. it required no coding. ask the doc what i mean....

[Audisthesia]

i have changed my doorchime. it required no coding. ask the doc what i mean....

Sounds like a cereal killer

[esemes]

what i cannot hear doesnt exist......

[digdah]

[Select] [46 - Central ConvElec.]
Coding
Long Coding Helper
Byte 15
Bit 3, Set New value: 1



Please note, you count the bits from RIGHT to LEFT starting with 0. So bit 3 is fourth position from right as shown in the image:

When I went into my C7 Byte 15 was all zeros. I tried turning just turning on bit 3, no dice, then bit 0 and 3 no dice. So I turn on bits 0-3 and that worked.

[Gunmeister]

When I went into my C7 Byte 15 was all zeros. I tried turning just turning on bit 3, no dice, then bit 0 and 3 no dice. So I turn on bits 0-3 and that worked.

I can confirm this worked on a C7.5 OBDeleven wouldnt work but using VCDS did. Interior lights are still working. Car does not make buzzing noise with door open with ignition on or car on with door open.

2016 A6 TDI*|*Mugello Blue, Pearl Effect Exterior | Alabastar White Interior | Audi Exclusive Line | Eucalyptus Natural Wood Decorative Inlays | Prestige Package | Comfort Seating Package | Driver Assistance Package | S Line Sport Package | 20" Black Optic Package | Cold Weather Package | Audi All Weather Mats*| 18% Ceramic Film Windows | 70% Ceramic Film Windshield | Thinkware F800 Pro Dash Cam | iDatastart VWX CMVWXA0 Remote Start*| Auto Hold Activated | ESCORT Radar Max 360c*| 1 of 1 for 2016

[Audisthesia]

When I went into my C7 Byte 15 was all zeros. I tried turning just turning on bit 3, no dice, then bit 0 and 3 no dice. So I turn on bits 0-3 and that worked.

Well, each vehicle stock binary for byte 15 can vary depending. Mine was 01000111 and others stock was 00000111.

This highlights why it is very important to only change the correct bit. My vehicle obviously has some different setting in bit 7 and we don't know what it's for. You know Audi, 50K variables and configurations in a C7/7.5.

It also highlights why it is VERY important to make some sort of backup PRIOR to changing ANYTHING. Use your phones camera, PC screenshot, whatever.

[Nachos Libres]

CONFIRMED this work on C7.5 as well. Although Dasquade math is bad.... 2 + 4 + 8 + 32 = 46 (not 48)

Boom, thanks for this guys. Have had efficiency mode for a long time but rarely use it because I don't like how in this mode the car suspension rides higher, how it muffles the exhaust, and how slow to react the adaptive cruise control is. This fixes all of that, thanks!

Now we just need someone to figure out how to add traffic sign recognition - though I'm guessing that isn't possible without a program.

[esemes]

After reading these latest posts, I feel like I need to turn in my nerd card.....

well done.

[back13a6]

here are some photos, I can not get the channel 98 to work. I can do the byte 15 no problem.

- - - Updated - - -

Scrrenshot of the issue?

I attached some photos.

[Dasquade]

Boom, thanks for this guys. Have had efficiency mode for a long time but rarely use it because I don't like how in this mode the car suspension rides higher, how it muffles the exhaust, and how slow to react the adaptive cruise control is. This fixes all of that, thanks!

Now we just need someone to figure out how to add traffic sign recognition - though I'm guessing that isn't possible without a program.

Glad to see you use it and are happy with it :). I suppose i always overlooked efficiency mode as i personally never ride in that, but i suppose lately many do use it because of the COD on in that mode right? My tune had the COD written out years ago but now with DS1 it might come in handy i guess. Anyway, glad it is usefull for you (i was actually not really planning to post the code for it as i didn't knew it would be needed for anybody lol).

What you mean with traffic sign recognition? You mean if somebody didn't had it on the car before and wanted to add it?
Like said, lots of coding availible on the german boards (motortalk.de) but bit harder to find and almost all in german language (translating often is bit off...).

[Dasquade]

Did I miss the no radio volume mod somewhere?

https://www.audizine.com/forum/showt...me-Mute-Unmute
Like posted there, normally one should be able to adjust the volume through the green hidden menu but in the past i wasn't able to get the value to be saved. Might be something i do wrong (maybe i didn't go back to main menu screen before rebooting the mmi or something else). Apperently it does work for some, just didn't had time yet to retry it again in the green menu. For the quick fix, i just selected my jukebox source (that is empty) so it gives me silence when i start the car. If you do have music in your jukebox, you could also insert a black sd card and select that one as your source....downside offcourse is you always need to manually activate the radio or different source if you do want to have music and redo it before shutting down the car.
I tend to enjoy a quick entry when i set in the car and 99% of the time just enjoy the sound of my V8 so the downside isn't there for me :).

[Audisthesia]

Boom, thanks for this guys. Have had efficiency mode for a long time but rarely use it because I don't like how in this mode the car suspension rides higher, how it muffles the exhaust, and how slow to react the adaptive cruise control is. This fixes all of that, thanks!

Now we just need someone to figure out how to add traffic sign recognition - though I'm guessing that isn't possible without a program.

If your a US vehicle, nope, not possible.

here are some photos, I can not get the channel 98 to work. I can do the byte 15 no problem.

- - - Updated - - -



I attached some photos.

What year/model is your vehicle?

[Audisthesia]

https://www.audizine.com/forum/showt...me-Mute-Unmute
Like posted there, normally one should be able to adjust the volume through the green hidden menu but in the past i wasn't able to get the value to be saved. Might be something i do wrong (maybe i didn't go back to main menu screen before rebooting the mmi or something else). Apperently it does work for some, just didn't had time yet to retry it again in the green menu. For the quick fix, i just selected my jukebox source (that is empty) so it gives me silence when i start the car. If you do have music in your jukebox, you could also insert a black sd card and select that one as your source....downside offcourse is you always need to manually activate the radio or different source if you do want to have music and redo it before shutting down the car.
I tend to enjoy a quick entry when i set in the car and 99% of the time just enjoy the sound of my V8 so the downside isn't there for me :).

OK, that answers that one. Not going to be possible on a C7.5. The green menu was drastically changed from 7 to 7.5

[Nachos Libres]

What you mean with traffic sign recognition? You mean if somebody didn't had it on the car before and wanted to add it?
Like said, lots of coding availible on the german boards (motortalk.de) but bit harder to find and almost all in german language (translating often is bit off...).

Traffic sign recognition where the camera will read the speed limit, display it in the gauge cluster and HUD and can also use it to adjust adaptive cruise control: https://www.youtube.com/watch?v=CLxTMc99Dfc

If your a US vehicle, nope, not possible.

Yeah, that's what I was thinking, though I have found where people have purchased this program for $200 or so and it gives them the ability, even on US vehicles:
https://www.kufatec.com/en/coding-di...number=40225-1

[back13a6]

If your a US vehicle, nope, not possible.



What year/model is your vehicle?

2013 A6 premium plus 3.0 quarto.

[Dasquade]

Yes i know traffic sign recognition since my euro car came equiped with it. Wasn't aware this wasn't an availible option for other countries and no idea if the kufatec coding works (afaik the image progressing camera software looks for the white round with red border signs, i suppose in the US it uses different signs but maybe the software can be recoded of opened to other regions and signs). It does work perfect....sadly our country decided to remove all 70km/h signs and one needs to fall back on other signs (leaving 'urban' signs or untill next crossing....). Nice move Belgium (rolls eyes). Luckly GPS info helps the system....

[Audisthesia]

Traffic sign recognition where the camera will read the speed limit, display it in the gauge cluster and HUD and can also use it to adjust adaptive cruise control:

Yeah, that's what I was thinking, though I have found where people have purchased this program for $200 or so and it gives them the ability, even on US vehicles:
https://www.kufatec.com/en/coding-di...number=40225-1

Yes i know traffic sign recognition since my euro car came equiped with it. Wasn't aware this wasn't an availible option for other countries and no idea if the kufatec coding works (afaik the image progressing camera software looks for the white round with red border signs, i suppose in the US it uses different signs but maybe the software can be recoded of opened to other regions and signs). It does work perfect....sadly our country decided to remove all 70km/h signs and one needs to fall back on other signs (leaving 'urban' signs or untill next crossing....). Nice move Belgium (rolls eyes). Luckly GPS info helps the system....

I've commented on this issue in other threads. I've contacted Kufatec directly myself. It is NOT possible on US cars.

2013 A6 premium plus 3.0 quarto.

Yours is probably just a different channel #. My advice would be to go down channel by channel... i.e.98 97 96.... until you find one with a value of 1, then set it to 0 and see if it works. And remember what channel you change so if it doesn't work you can go back and restore it to stock.

[jakubx80]

I've commented on this issue in other threads. I've contacted Kufatec directly myself. It is NOT possible on US cars.



Yours is probably just a different channel #. My advice would be to go down channel by channel... i.e.98 97 96.... until you find one with a value of 1, then set it to 0 and see if it works. And remember what channel you change so if it doesn't work you can go back and restore it to stock.

Can you please comment what's not possible? No sign recognition at all or recognize when leaving urban areas?

Is HUD required or would it work on a car without HUD?

Sent from my SM-G965U using Tapatalk

[back13a6]

I've commented on this issue in other threads. I've contacted Kufatec directly myself. It is NOT possible on US cars.



Yours is probably just a different channel #. My advice would be to go down channel by channel... i.e.98 97 96.... until you find one with a value of 1, then set it to 0 and see if it works. And remember what channel you change so if it doesn't work you can go back and restore it to stock.

I went 20 up and 20 down and none with a 1. Any other help would be appreciated.

[akingzkid]

here are some photos, I can not get the channel 98 to work. I can do the byte 15 no problem.

- - - Updated - - -



I attached some photos.

This sounds silly but I will say it anyway. Are you clicking the "Read" button to the right of it? If not, you need to, if memory serves me correctly.

[akingzkid]

[Select] [46 - Central ConvElec.]
Coding
Long Coding Helper
Byte 15
Bit 3, Set New value: 1



Please note, you count the bits from RIGHT to LEFT starting with 0. So bit 3 is fourth position from right as shown in the image:

I see there has been lots of discussion on this in the few days since I made my post.

This is spot on. This is what I did and it worked. This made it no longer beep when opening the door with the engine running. I did not have the 1 in the second place from the left though.

[Nachos Libres]

I've commented on this issue in other threads. I've contacted Kufatec directly myself. It is NOT possible on US cars.

Well that's a bummer.

[Carl0s]

Well well, today had some time to play with the coding and my results are following:

- if i start the car and open the door, i get the nuclear alarm.

- if i start the car, drive a bit and open the door, there is no alarm (engine running). If i step out of the vehicle, where i previously got the ”key not in vehicle” warning, the engine now shuts down.

- interior lights work again 👍 This was done earlier but i only noticed it after trying to mute the alarm. Problem was that on OBDeleven, central electrics (09) long coding there is ”Background lightning” and ”interior lightning adaptation”... Interior lightning adaptation (even tho in the MMI its called background lightning) is the ”mood lightning” in the footwells/side panels, and background lightning just kills the interior lights.

As a added bonus, i due to the magnificent feature of OBDeleven always returning to Byte 0 after programming, i successfully fucked up the long coding in comfort module 🤦 The person who came up with the phrase “If you want something done right, you better do it yourself” didn’t take in to account, that myself is a fucking idiot.