***USE AT YOUR OWN RISK I AM NOT RESPONSIBLE FOR ANYTHING THAT MAY HAPPEN***
Here's the list I've compiled so far:
Enable Automatic Gear selection shown in DIS
Enable Automatic PDC Front
Enable ACC default distance in MMI
Enable Laptimer shown in DIS
Increase time required to open trunk lid with remote key
Double beep on opening
Enable Sports Computer
Disable Seatbelt Warning
Enable Needle Sweep
Adaption Changes for "Chirps" when LOCKING the car
Adaption Changes for number of "Indicator Flashes" when LOCKING the car
Adaption Changes for "Chirps" when UN-LOCKING the car
Adaption Changes for number of "Indicator Flashes" when UN-LOCKING the car
DRL (Daytime Running Lights) On/Off Option in MMI
Enable ability to Rip CD's to MMI "Jukebox"
Audi Active Lane Assist - Steering Vibration Adjustment
Lock When Driving
Disable "Low Wind Noise" Stop point on Sunroof
Parking Assist Camera - Turn Off Speed
Seat Symmetry + Passenger Seat Control
Enable & Pair a Second Phone via Bluetooth simultaneously
Enable Ability to lock car with Engine running
Disable rear wiper
De-Activation of Start-Stop
Enable Coming home
Activation of automatic opening of the car when approaching
Disable side marker
Increase number of flashes when you nudge the stalk
Turn off range limiter for Comfort Window System
Deactivate Key Lock Range
Increase Steering Wheel Heater Temp
Activate rear tail lights with DRL in Auto mode
Enable Emergency braking
Combine the park assist 360 camera view with the OPS (Optical Parking Sensors) In the display
Change ventilated seat cooling fan speeds for each of the 3 setting
Change the Heated Seats temp in each stage
Automatic Parking Brake
Reset MMI
Press up on Nav and Radio while pressing on the center wheel
__________________________________________________ _____________________
Security Codes
09 - Central Electrics: 20113
13 - Auto Distance Regulation: 20103
6D - Trunk Electric: 12345
57 - TV Tuner: 20103
CA - Sunroof: 20103
__________________________________________________ _____________________
Enable Automatic Gear selection shown in DIS
[02 – Auto Trans] [Adaptation – 10]
Select “Single Gear Display” from top channel drop down menu
Select “D on/S on” from New value drop down menu
__________________________________________________ _____________________
Enable Automatic PDC Front
[09 – Central Elect.] [Coding - 07]
Select Long Coding Helper
Select Bye 37
Check Bit 1
Long Coding Helper
__________________________________________________ _____________________
Enable ACC default distance in MMI (might need security code)
[13 - Auto Dist. Reg][Adaptation - 10]
Select "Distance basic setting option" in dropdown
Select "On" from New value drop down
Save and reset MMI
__________________________________________________ _____________________
Enable Laptimer shown in DIS
[17 – Instrument Cluster] [Coding – 07]
Select Long Coding Helper
Write down coding as backup
Select byte 01
Enable bit 03
__________________________________________________ _____________________
Increase time required to open trunk lid with remote key
[46 - Central Convenience][Adaptation - 10]
Scroll down and find channel "Time for opening rear lid with remote control"
Load Stored Value (should be 800 ms)
Enter new value in "ms". Example: 2000, Max: 5000
__________________________________________________ _____________________
Double beep on opening (didn't work on my A4B9 after locking, waiting and unlocking, may need to wait longer)
[46 - Central Convenience][Adaptation - 10]
Scroll down and find channel "sounder_settings-beeptime_opening_central_locking"
change from "no_beep" to "double_beep"
__________________________________________________ _____________________
Not sure if this helps Canadian "non-AudiConnect" owner to enable the modem but might be worth a try
[5F - Information Electronics][Adaptation - 10]
Select "Vehicle configuration-LTE_module"
was "activated" in my US A4B9
On the topic of using an external SIM card for data, there is an adaptation channel in 5F called "Internal SIM card; use" with the default setting of "always".
Changing this to "automatic" extends the Data Connection Settings menu and allows entering an APN, username and password.
The MIB2 detected the required APN automatically based on the SIM card inserted just like older MMI head units.
__________________________________________________ _____________________
Enable Sports Computer
[17 – Instrument Cluster] [Coding – 07]
Select Long Coding Helper
Select Byte 10
Enable Bit 2
__________________________________________________ _____________________
Disable Seatbelt Warning
[17 – Instrument Cluster] [Coding – 07]
Select Long Coding Helper
Select Byte 0
Disable Bit 2
__________________________________________________ _____________________
Enable Needle Sweep
[17 – Instrument Cluster] [Coding – 07]
Select Byte 1
Select Bit 0
__________________________________________________ _____________________
Tailgate Opening Delay - Via Remote Key Fob
[46 - Central Convenience] [Adaptation - 10]
Scroll down and find channel "Time for opening rear lid with remote control"
Load Stored Value (should be 800 ms)
Enter new value in "ms". Example: 2000
__________________________________________________ _____________________
Lock/Unlock "Chirp"
[46 - Central Convenience] [Coding - 07]
Select Byte 4
Select Bit 6
__________________________________________________ _____________________
Adaption Changes for "Chirps" when LOCKING the car:
[46 - Central Convenience] [Adaptation - 10]
Find channel "(2)-sounder_settings-beeptime_closing_central_locking"
Default Value is "single_beep"
If you want a single "chirp" when you lock the car, leave this setting as is.
If you want a double "chirp" when you lock the car, change the value to "double_beep"
__________________________________________________ _____________________
Adaption Changes for number of "Indicator Flashes" when LOCKING the car:
[46 - Central Convenience] [Adaptation - 10]
Find channel "(3)-Turn Signal control-Confirmation flashing locking central locking; flashing cycles"
Default Value is "1"
If you want a single indicator "flash" when you lock the car, leave this setting as is.
If you want a double indiactor "flash" when you lock the car, change the value to "2"
__________________________________________________ _____________________
Enable "Beep on Unlock"
[46 - Central Convenience] [Adaptation - 10]
Find channel "(1)-central_locking_system-beep_at_opening"
Default Value is "Off"
Change Value to "On"
__________________________________________________ _____________________
Adaption Changes for "Chirps" when UN-LOCKING the car:
[46 - Central Convenience] [Adaptation - 10]
Find channel "(4)-sounder_settings-beeptime_opening_central_locking"
Default Value is "no_beep"
If you do NOT want a "chirp" of any sort when you UN-lock the car, leave this setting as is.
If you want a single "chirp" when you UN-lock the car, change the value to "single_beep"
If you want a double "chirp" when you UN-lock the car, change the value to "double_beep"
__________________________________________________ _____________________
Adaption Changes for number of "Indicator Flashes" when UN-LOCKING the car:
[46 - Central Convenience] [Adaptation - 10]
Find channel "(3)-Turn Signal control-Confirmation flashing unlocking central locking; flashing cycles"
Default Value is "2"
If you want a double indicator "flash" when you UN-lock the car, leave this setting as is.
If you want a single indicator "flash" when you UN-lock the car, change the value to "1"
If you want a NO indicator "flash" when you UN-lock the car, change the value to "0"
__________________________________________________ _____________________
DRL (Daytime Running Lights) On/Off Option in MMI
[09 – Central Elect.] [Coding - 07]
Select Long Coding Helper
Select Byte 2
Select Bit 1
__________________________________________________ _____________________
Enable ability to Rip CD's to MMI "Jukebox"
[5F - Information Electr] [Coding - 07]
Select Long coding helper
Select Byte 24
Select Bit 5
Adaption:
[5F - Information Electr] [Adaptaion - 10]
Module 5F - Information Electr
Scroll down and find channel "(2)-Copy multimedia data-Optical drive"
Load Stored Value (should be set to "Off")
Change to "On"
__________________________________________________ _____________________
Audi Active Lane Assist - Steering Vibration Adjustment
[A5 - Front Sens. Driver Assist] [Adaptation - 10]
Scroll down and find channel "IDE05985-Directional stab. assist ; intensity; steering wheel vibration"
Load Stored Value (should be set to "Medium")
Change to either "Weak / Medium / Strong"
__________________________________________________ _____________________
Lock When Driving
[46 - Central Convenience] [Coding - 07]
Module 46 - Central Convenience
Select Long coding helper
Select Byte 35
DE-Select Bit 0
__________________________________________________ _____________________
Disable "Low Wind Noise" Stop point on Sunroof
[CA - Sunroof] [Security Access]
[Adaption]
Find channel "IDE09451-MAS08937-Travel path-Sliding Position: intermed. pos."
Value should be "Active"
Change to "Not Active"
__________________________________________________ _____________________
Parking Assist Camera - Turn Off Speed
[Adaptation - 10]
Scroll down and find channel "Switch off speed for park assist"
Load Stored Value (should be set to "10 Kph / 6 Mph")
Change to another value. Example "20" (which is about 12 Mph)
__________________________________________________ _____________________
Seat Symmetry + Passenger Seat Control
**You need to do the SAME coding in Modules 06 and 36.**
[06 - Passenger Seat Module][Coding - 07]
Select Long coding helper
Select Byte 2
Select Bit 5
Select Byte 6
Select Bit 1
[36 - Driver Seat Module][Coding - 07]
Select Long coding helper
Select Byte 2
Select Bit 5
Select Byte 6
Select Bit 1
__________________________________________________ _____________________
Enable & Pair a Second Phone via Bluetooth simultaneously
[5F - Information Electr] [Adaptaion - 10]
Scroll down till you find channel "IDE03471-ENG130247-Vehicle configuration-Support_second_phone" (name may be slightly shorter in ODBEleven)
Load Stored Value (Default will be "Not Active")
Change to "Active"
__________________________________________________ _____________________
Enable Ability to lock car with Engine running
[46 - Central Convenience] [Coding - 07]
Select Long Coding Helper
Select Byte 9
Select Bit 7
__________________________________________________ _____________________
Disable rear wiper
[09 - Central Electrics] [Coding - 07]
Select Long Coding helper
Select Byte 12
Set Bit 6 to 0
Set Bit 7 to 1
[09 - Central Electrics] [Coding - 07]
Select Long Coding helper
Select Byte 12
Select rear_wiper
Set value to not_installed
__________________________________________________ _____________________
De-Activation of Start-Stop
[19 - CAN Gateway] [Adaptation - 10]
Start-Stop Voltage Limit>12V (New Value)
__________________________________________________ _____________________
Enable Coming home
[09 - Central Electrics] [Coding - 07]
Select welcome_light
Set value to 1
__________________________________________________ _____________________
Activation of automatic opening of the car when approaching
The cart opens automatically when you are about 1-2m away.
[46 - Central Convenience] [Coding - 07]
automatic_opening
set to active
__________________________________________________ _____________________
Disable side marker
[09 - Central Electrics] [Coding - 07]
Select Long Coding Helper
Select Byte 6
Select Bit 4
[09 – Cent. Elect.] [Coding - 07]
Long Coding Helper
Select Byte 10
Uncheck Bit 3
__________________________________________________ _____________________
Increase number of flashes when you nudge the stalk
[46 - Central Convenience] [Adaptation - 10]
Turn Signal Control => Freeway flashing cycles
Change value from 3 to 4 (1-5 possible)
__________________________________________________ _____________________
Turn off range limiter for Comfort Window System
[46 - Central Convenience]
Coding->comfort_operation_range_limitation->not active
__________________________________________________ _____________________
I haven't done mine, but apparently you can increase the range to lock / unlock.
Deactivate Key Lock Range
[46 - Central Convenience]
Coding->range_limitation_lock-> not active
Deactivate Key Opening Range
[46 - Central Convenience]
Coding->range_limitation_opening-> not active
__________________________________________________ _____________________
Increase Steering Wheel Heater Temp
**should not go above 38C**
[16 - Steering Column Electronics]
Adaptation: steering wheel heater
__________________________________________________ _____________________
Turns on low beam as well as high beam when you flash people with headlights off
[09 - Central Electrics]
Coding -> lowbeam_at_flash-> activate
__________________________________________________ _____________________
Activate rear tail lights with DRL in Auto mode
[09 - Central Electrics]
Coding->signiturelight_config-> signaturelight_with_tailight
__________________________________________________ _____________________
Enable Emergency braking
[46 - Central Convenience] [Coding - 07]
Select Long Coding Helper
Select Byte 21
Set Bit 0 to 1
If ACC and Pre-sense
Set Bit 2 to 1
Set Bit 3 to 1
Select Byte 36
Set Bit 0 to 1
Set Bit 1 to 1 (for hazards to flash)
__________________________________________________ _____________________
Combine the park assist 360 camera view with the OPS (Optical Parking Sensors) In the display
[17 - Instruments][09 - Central Electronics] [Adaptation - 10]
IDE01170-Visual display for park assist
Original Value - with OPS display
New Value - with OPS 360°
__________________________________________________ _____________________
Change ventilated seat cooling fan speeds for each of the 3 setting
**Max increase is 10% over the default setting**
[09 - Central Electronics] [Adaptation - 10]
IDE10322-MAS01366-Seat ventilation; micro adjust.-Stage 3
Stored value 0 %
New Value - 10%
IDE10322-MAS01365-Seat ventilation; micro adjust.-Stage 2
Stored value 0 %
New Value - 10%
IDE10322-MAS01364-Seat ventilation; micro adjust.-Stage 1
Stored value 0 %
New Value - 10%
__________________________________________________ _____________________
Change the Heated Seats temp in each stage
**5 DEGREES + OR - IS MAX VALUE**
[09 - Central Electronics] [Adaptation - 10]
IDE10321-MAS01364-Seat heater: micro adjust.-Stage 1
Stored value 0 °C
IDE10321-MAS01364-Seat heater: micro adjust.-Stage 2
Stored value 0 °C
IDE10321-MAS01364-Seat heater: micro adjust.-Stage 3
Stored value 0 °C
__________________________________________________ _____________________
C to display SQ7 dials
In module 17 go into long coding
Then change vehicle variant to "derivative 2"
Apply changes
Come out of long coding
Choose reset
Then hard reset
MMI startup screen to display SQ7 logo:
in module 5F long coding, change "byte_18_Screenings" from 27 to 28, reboot MMI
__________________________________________________ _____________________
Automatic Parking Brake
[03 - Brakes] [Adaptation - 10]
Automatic Parking Brake -> Activited
***USE AT YOUR OWN RISK I AM NOT RESPONSIBLE FOR ANYTHING THAT MAY HAPPEN***
**I have not tried all of these, and some i have tried where the coding takes, but it does not do what it is supposed to.**
Originally Posted by Mpower2170
Reply With Quote
Bookmarks