Audizine - An Automotive Enthusiast Community

Results 1 to 14 of 14
  1. 04-10-2016 11:15 PM #1
    swededA4
    swededA4 is offline
    Veteran Member Four Rings swededA4's Avatar
    Join Date
    Apr 02 2010
    AZ Member #
    57065
    My Garage
    Usually other peoples Audi's
    Location
    Greenville,SC

    Coil Pack Conduit

    Guest-only advertisement. Register or Log In now!
    Hey everyone,
    Is there a DIY or any information on installing the B7 audi A4 2.0t coil pack conduit?
    I have searched, I have googled and I have found nothing. Maybe I am wording it wrong. I know someone has done it. I just want to make sure I am doing it "right" before I start cutting.

    Thanks in advance

    This is the part I am referring to.

    Last edited by swededA4; 04-11-2016 at 10:06 AM.
    Motoza PODI BAE Parts4Euro

    BAE turbo, 550 injectors, Greddy FMIC, S4 TB,Snow meth kit, Privat Werks 19 X 8.5, Solowerks Coilovers, 034 end links, RS4 rear sway, Deval Splitter, 15% tint, 3" full exhaust with Borla 40357's, JHM trio, PODI Stepper, Recaro's
    Reply With Quote Reply With Quote  
  2. 04-11-2016 08:14 AM #2
    ADCS
    ADCS is offline
    Veteran Member Four Rings ADCS's Avatar
    Join Date
    Jan 06 2009
    AZ Member #
    37126
    Location
    Toronto

    The part splits into 2 halves and just clips over the wires which is why you can't find a DIY. Just put it on. Wrap some tape over the free ends if you want secure it.
    B6 2.7t BEL tuned by Bische
    B7 2.0t
    Reply With Quote Reply With Quote  
  3. 04-11-2016 09:53 AM #3
    swededA4
    swededA4 is offline
    Veteran Member Four Rings swededA4's Avatar
    Join Date
    Apr 02 2010
    AZ Member #
    57065
    My Garage
    Usually other peoples Audi's
    Location
    Greenville,SC

    Quote Originally Posted by ADCS View Post
    The part splits into 2 halves and just clips over the wires which is why you can't find a DIY. Just put it on. Wrap some tape over the free ends if you want secure it.
    OK, It appeared there was more to it than that. Which is why I was asking. As I tried to put it on yesterday and it looked like the factory protective coating needed to be removed. As well the rubber boot that goes on the coil pack connector. Have you installed the conduit on your B6 A4?
    Motoza PODI BAE Parts4Euro

    BAE turbo, 550 injectors, Greddy FMIC, S4 TB,Snow meth kit, Privat Werks 19 X 8.5, Solowerks Coilovers, 034 end links, RS4 rear sway, Deval Splitter, 15% tint, 3" full exhaust with Borla 40357's, JHM trio, PODI Stepper, Recaro's
    Reply With Quote Reply With Quote  
  4. 04-11-2016 01:57 PM #4
    CyberPMG
    CyberPMG is offline
    Veteran Member Four Rings CyberPMG's Avatar
    Join Date
    Feb 23 2004
    AZ Member #
    806
    My Garage
    2004 A4 1.8T Ultrasport 6MQ
    Location
    Stow, OH

    Nothing needs to be removed from the ignition harness or boots. The conduit simply snaps open, drop in the harness, and snap close.
    USP CLUB MEMBER #34

    2004 A4 1.8T USP - GT2871R Eliminator - Motoza program - Over 375k miles!
    2015 S5 - Sepang Blue - 6spd w/ Sport Diff - stock(ish)
    Reply With Quote Reply With Quote  
  5. 04-12-2016 12:01 AM #5
    tHatOne guY
    tHatOne guY is offline
    Veteran Member Three Rings tHatOne guY's Avatar
    Join Date
    Aug 20 2012
    AZ Member #
    99020
    My Garage
    06' Yamaha R1...Raven
    Location
    Mesa, Az

    Any pics of it once installed? I wanna do this to mine as well. Just wanna see if it's as clean looking as I hope.
    Reply With Quote Reply With Quote  
  6. 04-12-2016 12:15 AM #6
    evo_ski
    evo_ski is offline
    Veteran Member Four Rings evo_ski's Avatar
    Join Date
    Mar 15 2010
    AZ Member #
    56121
    Location
    Bothell

    For extra bonus points do the b6 s4 fuel injector conduit as well.
    Costco 92 Octane Gas - MANN Air Filter - 235/35/19 Tires w/ 36 PSI (cold) Tire Pressure - Grey Plastic Valve Stem Caps - 0° Front Toe - Rotella T6 5W-40 - 2 OEM B6 Keys - 18x8" Spare - Coin & Pen Filled Center Console - Rain-X on all 8 windows & Napa Cold Temp Washer Fluid - Bosch Wiper Blades (Valeo wipers suck big time!) - S4 Trunk Latch - Craftsman Tire Pump w/ Automatic PSI Shutoff - Belly Pan Delete (Weight Savings) - 3D Printed Rear Warning Triangle latch - 174,000 Miles & Counting
    Reply With Quote Reply With Quote  
  7. 04-12-2016 12:22 AM #7
    swededA4
    swededA4 is offline
    Veteran Member Four Rings swededA4's Avatar
    Join Date
    Apr 02 2010
    AZ Member #
    57065
    My Garage
    Usually other peoples Audi's
    Location
    Greenville,SC

    Have any of you installed this? Can you share some pictures of your snap on install?

    Sent from my Nexus 6 using Tapatalk
    Motoza PODI BAE Parts4Euro

    BAE turbo, 550 injectors, Greddy FMIC, S4 TB,Snow meth kit, Privat Werks 19 X 8.5, Solowerks Coilovers, 034 end links, RS4 rear sway, Deval Splitter, 15% tint, 3" full exhaust with Borla 40357's, JHM trio, PODI Stepper, Recaro's
    Reply With Quote Reply With Quote  
  8. 04-12-2016 12:46 AM #8
    evo_ski
    evo_ski is offline
    Veteran Member Four Rings evo_ski's Avatar
    Join Date
    Mar 15 2010
    AZ Member #
    56121
    Location
    Bothell

    It needs a bit of modifying to make the wires fit, but if you have to rebuild your harness it definitely makes it look pretty clean.



    Costco 92 Octane Gas - MANN Air Filter - 235/35/19 Tires w/ 36 PSI (cold) Tire Pressure - Grey Plastic Valve Stem Caps - 0° Front Toe - Rotella T6 5W-40 - 2 OEM B6 Keys - 18x8" Spare - Coin & Pen Filled Center Console - Rain-X on all 8 windows & Napa Cold Temp Washer Fluid - Bosch Wiper Blades (Valeo wipers suck big time!) - S4 Trunk Latch - Craftsman Tire Pump w/ Automatic PSI Shutoff - Belly Pan Delete (Weight Savings) - 3D Printed Rear Warning Triangle latch - 174,000 Miles & Counting
    Reply With Quote Reply With Quote  
  9. 04-12-2016 07:38 AM #9
    audireme
    audireme is offline
    Established Member Two Rings
    Join Date
    Jun 29 2014
    AZ Member #
    260271
    Location
    America

    I installed it on a B5 AWM, cut out the boots, otherwise it cannot snap over the connector. Made a little hole for the ground wire, and shaved a bit off the end to fit next to the SAIP pipe. But other than removing the boots and ties that hold the harness to the valve cover, no other modifications needed to the harness.
    Reply With Quote Reply With Quote  
  10. 04-12-2016 10:56 AM #10
    CyberPMG
    CyberPMG is offline
    Veteran Member Four Rings CyberPMG's Avatar
    Join Date
    Feb 23 2004
    AZ Member #
    806
    My Garage
    2004 A4 1.8T Ultrasport 6MQ
    Location
    Stow, OH

    I have the conduit on my car. Will be doing a coil pack and spark plug replacement very soon (hopefully this weekend). Will take pics.

    What's this about a fuel injector conduit???
    USP CLUB MEMBER #34

    2004 A4 1.8T USP - GT2871R Eliminator - Motoza program - Over 375k miles!
    2015 S5 - Sepang Blue - 6spd w/ Sport Diff - stock(ish)
    Reply With Quote Reply With Quote  
  12. 04-12-2016 11:02 AM #11
    jpulll
    jpulll is offline
    Veteran Member Four Rings jpulll's Avatar
    Join Date
    Jun 19 2014
    AZ Member #
    256344
    Location
    Ohio

    Quote Originally Posted by CyberPMG View Post
    What's this about a fuel injector conduit???
    Interested too. I had to redo my injector harnesses and need something better than what i have - some poopy autozone conduit.
    2003 A4 1.8T 5-spd Frankenturbo'd.
    Reply With Quote Reply With Quote  
  13. 04-12-2016 12:14 PM #12
    Matt Devo
    Matt Devo is offline
    Veteran Member Four Rings
    Join Date
    Feb 17 2004
    AZ Member #
    607
    Location
    Liberty Hill, TX

    2012 TT-RS | Sepang/Ebony
    2014 Allroad | Glacier/Ebony (sold and bought back)

    Sold: 2007 RS4 | Sprint/Ebony

    RIP 2002 A4 2.0TQM Denim/Ebony, 243k
    FWD->AWD, Bische-tuned GT2871R
    Reply With Quote Reply With Quote  
  14. 04-12-2016 06:50 PM #13
    jursch2211
    jursch2211 is offline
    Veteran Member Four Rings jursch2211's Avatar
    Join Date
    Feb 05 2008
    AZ Member #
    24941
    Location
    Illinois

    Ben, I tried installing the coilpack conduit with no success. After trying to get it to fit I think the rubber boots needed to be removed. It just did not fit. Sorry I couldn't give you more info but I'm curious to know how everyone else is getting them on.
    || APR | BW K04-015 | ER FMIC | OEM S4/RS4/R8 Parts | '10 RNS-E | Hotchkis | Adam's Rotors | Podi | OCarbon | Euro Headlights | Euro Color DIS | Euro MKII TT MFSW | Euro Trunk | BBS | Vogtland Coilovers ||
    Reply With Quote Reply With Quote  
  15. 04-13-2016 12:44 AM #14
    swededA4
    swededA4 is offline
    Veteran Member Four Rings swededA4's Avatar
    Join Date
    Apr 02 2010
    AZ Member #
    57065
    My Garage
    Usually other peoples Audi's
    Location
    Greenville,SC





    Sent from my Nexus 6 using Tapatalk
    Motoza PODI BAE Parts4Euro

    BAE turbo, 550 injectors, Greddy FMIC, S4 TB,Snow meth kit, Privat Werks 19 X 8.5, Solowerks Coilovers, 034 end links, RS4 rear sway, Deval Splitter, 15% tint, 3" full exhaust with Borla 40357's, JHM trio, PODI Stepper, Recaro's
    Reply With Quote Reply With Quote  
« Previous Thread | Next Thread »

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules



    © 2001-2025 Audizine, Audizine.com, and Driverzines.com
    Audizine is an independently owned and operated automotive enthusiast community and news website.
    Audi and the Audi logo(s) are copyright/trademark Audi AG. Audizine is not endorsed by or affiliated with Audi AG.