Teaser 2.0T Coil packs...

[jibberjive]

$10 is not bad at all, but where? Anyone know?

I'm pretty sure he's saying that he makes/sells them, like the ones he made in his picture.

[ilyafil]

Just pulled the trigger on these!

Originally Posted by disrepos

or 6-packs, $55

http://www.onlinewholesaleparts.com/vwicc-004.html

Great find. Splice the harness to delete the ICMs, plus coils roughly $19 each, plus Touareg adapters $5 each. Around $200 total. Not bad at all!

[vtraudt]

I bought the red Bosch coils and red anodized spacers from Intergrated Engineering.
Very disappointed: I have no idea why in the world they did not make the spacer shape so that it covers up the (almost square) plug holes (like the 034 spacers seem to do). Now I have these ugly incovered holes in the corners.

Either they send me the wrong ones for my 1.8T AEB, or their designer has never seen an AEB engine.

http://ep.yimg.com/ca/I/yhst-1182956..._2246_29353469

It looks like THIS is what they should have shipped:

http://www.intengineering.com/media/...2.7t_red_1.jpg

[ilyafil]

You're right, they sent you the wrong adapters.

[disrepos]

[ilyafil]

I just ordered the $55 ones. You win!

[bengone1]

I am curious to know how long the leads are and if the wire is of good quality. Please let us know when you get them.

If not, I will try to track down a 3.0L harness. The way the engine wiring wraps around there should be more than enough for the job if you hack it at the ECU box.

Has anyone considered crimping on the Volvo ends and making this plug and play? Additional cost and connections, but it would be clean and simple.

[ilyafil]

I know the wires are about a foot long. (someone else on here already used those connectors) I'll let you know about the quality. Shouldn't be difficult to track down a 3.0 harness though.

I'm just going to eliminate the ICM plugs all together. Just cut, splice and heat shrink the wires. No plugs at all. :)

[ddillenger]

I know the wires are about a foot long. (someone else on here already used those connectors) I'll let you know about the quality. Shouldn't be difficult to track down a 3.0 harness though.

I'm just going to eliminate the ICM plugs all together. Just cut, splice and heat shrink the wires. No plugs at all. :)

Are you going to do the corresponding ecu mods for the 2.0 coils?

[CONTROL ONE]

Has anyone put together a new 'value' kit as of late?

1. best place to get the 2.0 coils?
2. best place to get the spacers? ($5/pc at genuineaudiparts.com or $10/pc for custom aluminum from member here)
3. best place to get the Volvo parts for the ICM delete?
4. best place to get the connections? (http://www.onlinewholesaleparts.com/vwicc-004.html or ABC MARTS on eBay)

[infinkc]

Has anyone put together a new 'value' kit as of late?

1. best place to get the 2.0 coils?
2. best place to get the spacers? ($5/pc at genuineaudiparts.com or $10/pc for custom aluminum from member here)
3. best place to get the Volvo parts for the ICM delete?
4. best place to get the connections? (http://www.onlinewholesaleparts.com/vwicc-004.html or ABC MARTS on eBay)

Think your list sums up the cheapest parts right now, the coils you might as well get from gap also if your getting the spacers, to save on shipping, i found they were the cheapest at the time also.
for the volvo parts, you can just splice the wires together, so bascilly no cost there.

6x coils @ 17.50 =105
6 harness plugs =55
6 adapters= 30

mod for under 200 now, wow.

[ilyafil]

Are you going to do the corresponding ecu mods for the 2.0 coils?

I wasn't aware that ECU mod is needed. But I'm a noob at tuning. Feel free to school me.

6x coils @ 17.50 =105

Coils are also available from RockAuto for $15 if you really want to go cheap, but not OEM. Probably Chinese. :)

[Timtheguru]

I wasn't aware that ECU mod is needed. But I'm a noob at tuning. Feel free to school me.



Coils are also available from RockAuto for $15 if you really want to go cheap, but not OEM. Probably Chinese. :)

I wasn't aware either, I didn't do any ECU mods, been running this for a while now.

[disrepos]

I just ordered the $55 ones. You win!

I just figured since I'd found a great price already, I'd throw a low offer to the Ebay seller. I didn't think they'd go for it, or they would at least counter.... but sometimes you just luck out.

Are you going to do the corresponding ecu mods for the 2.0 coils?

dd - are you referring to using the spark dwell table (KFSZT - voltage/rpm) from a 2.0TFSI file? Or are there other tables listed below that need to be considered as well?



Is anyone having problems running the FSI coil conversion without making changes to spark duration maps in your file? Cold start problems? Blowing Coil Packs? Other oddities?

[ilyafil]

I would like to know this as well.^^^

[jibberjive]

http://nefariousmotorsports.com/foru...ic=445.0title=

[fmars62]

I thought the 034 kit was just a direct bolt on with no wiring? So I am having trouble understanding what you did with the harness from ecstuning. Why do I need the harness, why cant you just switch everything with the 034 kit? Sorry may be a newb question

[Audone]

034 is plug and play... the harness is for those who want a cheaper DIY solution.


For the record I have had numerous cold starts without any issues.. and by cold I mean -20c and lower.

[ilyafil]

http://nefariousmotorsports.com/foru...ic=445.0title=

Good find. It makes sense to adjust the spark dwell, maybe make the coils last longer. But I guess people aren't having any problems leaving it stock.

[DiscoPotato]

Finished mine yesterday! Easy install.

[Mr. Merk]

How'd you do the ICM delete?

[DiscoPotato]

How'd you do the ICM delete?

Volvo 4 pin to Volvo 3 pin.

Omit pin 2.

[Timtheguru]

Looks great! I'd be worried about that gap though, driving around you'll get dirt/sand that falls down in there and when removing the spark plugs you'll get all that sand to fall down into the cylinders, unless you have a good vacuum that will get it all, and remember to vacuum every time you do plugs. I liked this way of sealing it off with the plastic adapters.



http://www.audizine.com/forum/showth...=1#post8465116

[DiscoPotato]

I figured I would just blow air in there push it all out.

That is if anything does get in there.

[Timtheguru]

I figured I would just blow air in there push it all out.

That is if anything does get in there.

More would get down in there with 6 APR funnels.

[DiscoPotato]

More would get down in there with 6 APR funnels.

Lol I know. I think I may attach one funnel per coilpack, upside down of course to make all debris exit the chamber .

[jibberjive]

What size is that shrink wrap that fit nicely over the connector boot notch?

[ilyafil]

I am curious to know how long the leads are and if the wire is of good quality. Please let us know when you get them.

If not, I will try to track down a 3.0L harness. The way the engine wiring wraps around there should be more than enough for the job if you hack it at the ECU box.

Has anyone considered crimping on the Volvo ends and making this plug and play? Additional cost and connections, but it would be clean and simple.

I got the coil connectors I ordered, they're very good quality. Wires are about 8-9" long and they came with heat shrink butt connectors. Shipped from inside US. BTW: There's a two week wait for the Touareg plastic coil adapters since the part number hit the forums. :) They have to come out of Deuchland.

[fmars62]

034 is plug and play... the harness is for those who want a cheaper DIY solution.


For the record I have had numerous cold starts without any issues.. and by cold I mean -20c and lower.

So if I buy the 034 kit i can just take out my old coil packs, put the 034's in and then i am good to go? no wire cutting, extending, etc.?

[infinkc]

So if I buy the 034 kit i can just take out my old coil packs, put the 034's in and then i am good to go? no wire cutting, extending, etc.?

Yep, no cutting or splicing required, only disconnect and reconnet.

[fmars62]

Yep, no cutting or splicing required, only disconnect and reconnet.

Sweet! I am definitely getting it then!

And I know it has been discussed before but In each thread about it there are different answers. What sparkplugs should i get and spacing should I run? I plan on going stage 2 and then F21 Stage 3, do I need different spacing for stage 2 and stage 3?

And with them being a direct bolt on it deletes ICM?

Thanks.

[CONTROL ONE]

Sweet! I am definitely getting it then!

And I know it has been discussed before but In each thread about it there are different answers. What sparkplugs should i get and spacing should I run? I plan on going stage 2 and then F21 Stage 3, do I need different spacing for stage 2 and stage 3?

And with them being a direct bolt on it deletes ICM?

Thanks.

Full 034 conversion costs upwards of $600, this method costs less than $200.

After seeing the gap the Toureg spacers leave, I would be more inclined to purchse the aluminum ones the AZ member makes for $10/pop.

[DiscoPotato]

What size is that shrink wrap that fit nicely over the connector boot notch?

1"

[fmars62]

Full 034 conversion costs upwards of $600, this method costs less than $200.

After seeing the gap the Toureg spacers leave, I would be more inclined to purchse the aluminum ones the AZ member makes for $10/pop.

http://www.034motorsport.com/ignitio...s-p-22156.html

That doesnt look like $600, if you include the coils it will be $450.

[Timtheguru]

http://www.034motorsport.com/ignitio...s-p-22156.html

That doesnt look like $600, if you include the coils it will be $450.

$577.00 with adapters and coils from 034.

[Blue AWD]

I got the coil connectors I ordered, they're very good quality. Wires are about 8-9" long and they came with heat shrink butt connectors. Shipped from inside US. BTW: There's a two week wait for the Touareg plastic coil adapters since the part number hit the forums. :) They have to come out of Deuchland.

I've got a set of these Touareg adapters if anyone is looking. PM me.

[fmars62]

$577.00 with adapters and coils from 034.

I stand corrected, forgot about those. Thanks.

[ilyafil]

I've got a set of these Touareg adapters if anyone is looking. PM me.

Oh, man I just placed the order. Coils and adapters. I went with the 07K905715F black coils (because more sneaky) Oh well, I can wait two weeks. :)

[disrepos]

Got mine from ABC Marts (ebay seller) last night as well. Same product as below, shipped from the same location in Pompano Beach, FL. I agree on the quality: They should do the job.

I got the coil connectors I ordered, they're very good quality. Wires are about 8-9" long and they came with heat shrink butt connectors. Shipped from inside US. BTW: There's a two week wait for the Touareg plastic coil adapters since the part number hit the forums. :) They have to come out of Deuchland.

[DonnieDark0]

Full 034 conversion costs upwards of $600, this method costs less than $200.

After seeing the gap the Toureg spacers leave, I would be more inclined to purchse the aluminum ones the AZ member makes for $10/pop.

Who is this member you speak of? i am interested.