USP: Fix your coil pack harness fast, cheap, and for good! Only $29!!!!

[Gregg@USP]

As many of you already know the 1.8T motors are plagued with coil pack and coil pack wire harness failures. USP is please to announce a cost and time effective way of correcting this problem. We present to you the ultimate coil pack repair kit. Below is an exert from the manufacturer.

Failed or burned up VW/Audi coil packs are most commonly caused by poor electrical connections or wire harness breaks. New connectors should be installed when replacing ignition coils especially if more than one coil pack fails. A loose connection can cause a voltage spike which may destroy or burn up the coil pack. Neighboring coil packs can also fail because wire harness connections may become bridged together because of exposed wires. The OEM connectors are not designed to be repeatedly unplugged and replugged in. VW/Audi recommends replacing the connector if there is any chance of a loose connection.

Fix the problem for good and install a new connector and leads when installing a new coil pack.

Each Kit includes:

(1) Coil pack clip
(4) Preinstalled high temperature leads with terminals installed
(3) Blue Heat Shrink connectors
(1) Red Heat Shrink connector
(1) Terminal removal tool
Full instructions



All this for $29! Click here to order and use coupon code "ignition" at checkout.

[T0M3K]

I would assume that it would work for 3.0 as well

[Gregg@USP]

I would assume that it would work for 3.0 as well

yes it will

[MikeWire]

Greg, what's the length on the leads?

[Gregg@USP]

Greg, what's the length on the leads?

15"

[JoshDub]

I wish I knew how to wire these up!

[mr_gp4e]

i have a 3.0 v6...My question is do you know how could i remove the harness from the red portion(not the coil - but the other end red thing that holds the 3 harnesses which connect to the coils)?> because my clips are all broken and I am planning to change them, but i would do it only if there is a simple way of removing the part shown in the pic from the red thingy?

[Gregg@USP]

i have a 3.0 v6...My question is do you know how could i remove the harness from the red portion(not the coil - but the other end red thing that holds the 3 harnesses which connect to the coils)?> because my clips are all broken and I am planning to change them, but i would do it only if there is a simple way of removing the part shown in the pic from the red thingy?

there is two small black T20 screws that hold the top of the loom down

[IRUNEDM]

anyone try these yet?

[Gregg@USP]

just got more in stock

[Gregg@USP]

Bump for Summer time

[Gregg@USP]

all orders have shipped

[Gregg@USP]

by by misfires

[aarononymous]

This would be more of an issue on the 1.8T with the exhaust right there IMO. I need to try this on mine...doesn't register a miss but you can feel it at times at idle and the wire insulation is cracked...

[Gregg@USP]

This would be more of an issue on the 1.8T with the exhaust right there IMO. I need to try this on mine...doesn't register a miss but you can feel it at times at idle and the wire insulation is cracked...

it should help out with that for sure

[Gregg@USP]

bye bye misfires

[marioss4]

will these work on a b5 s4 my wires are toast from the turbos

[Gregg@USP]

will these work on a b5 s4 my wires are toast from the turbos

we are working on one for the b5 s4 now, this one wont work

[JTAudet]

we are working on one for the b5 s4 now, this one wont work

these will work on the b5 and b6 a4 1.8t?

[Gregg@USP]

these will work on the b5 and b6 a4 1.8t?

it will work on a b6 a4 but not the b5

[Gregg@USP]

more in stock

[SLeal]

is there a 3.0 pack with 6 rather than paying for 2 sets and having left overs?

thanks

[Gregg@USP]

is there a 3.0 pack with 6 rather than paying for 2 sets and having left overs?

thanks

This is not per set, this is for each sylinder so a 3.0 would need 6 of these to change all the connections

[SLeal]

Gotcha...so much for reading! lol

Thanks

[Gregg@USP]

Gotcha...so much for reading! lol

Thanks

its ok

[[TSA] Oscar]

definately picking up a set, my wires are exposed on #2 cylinder ;)

[[TSA] Oscar]

also, whats the point of the terminal removal tool if it already comes assembled?

[[TSA] Oscar]

The discount doesn't even cover shipping, harsh!

[n7plus1]

how much for the tool only?

[Gregg@USP]

definately picking up a set, my wires are exposed on #2 cylinder ;)

you should get that fixed ASAP

also, whats the point of the terminal removal tool if it already comes assembled?

In case you don't want to change the leads

The discount doesn't even cover shipping, harsh!

This has been confusing me lately. I'm trying to figure out why people think that a sale price includes free shipping.

how much for the tool only?

They are $10

[n7plus1]

They are $10

on teh site?

[Gregg@USP]

on teh site?

they are not on site, email me at [email protected] to place your order