Audizine - An Automotive Enthusiast Community

Results 1 to 5 of 5
  1. 01-05-2009 01:45 PM #1
    drunknmunky408
    drunknmunky408 is offline
    Veteran Member Three Rings drunknmunky408's Avatar
    Join Date
    Sep 26 2006
    AZ Member #
    12032
    My Garage
    2001 A4 1.8T FWD - SOLD
    Location
    San Jose, CA

    FMIC install question...

    Guest-only advertisement. Register or Log In now!
    I took my bumper off and i'm about to get started on the FMIC. I have a question about the stock intercooler. There is a plug thats part of the intercooler... what do I do with that after I take out the stock one? The FMIC doesn't have a plug for me to use it. Do I disregard that?|

    TIA
    2001.5 Nogaro Blue S4 6spMT l Sports Package l Blue Alcantara Seats l APR Chip l Neuspeed Exhaust l Eclipse AVN6620 l AWE Boost Guage l AWE Pedals l NRG 230g Shift Knob l

    TEAM|AXION
    Reply With Quote Reply With Quote  
  2. 01-05-2009 01:50 PM #2
    Seerlah
    Seerlah is offline
    Veteran Member Four Rings Seerlah's Avatar
    Join Date
    Dec 05 2007
    AZ Member #
    23104
    Location
    A place between here and there

    Re: FMIC install question...

    I have not installed an FMIC myself, but that is your MAP sensor. You need to cut/weld a bung onto the piping going to the thorttle body then plug the MAP sensor into that. Only the DBW cars require this. Another should chimme in and grant proper procedure. And yes, you need that sensor.
    Reply With Quote Reply With Quote  
  3. 01-05-2009 01:50 PM #3
    fenderstrat1184
    fenderstrat1184 is offline
    Senior Member Two Rings fenderstrat1184's Avatar
    Join Date
    Oct 17 2006
    AZ Member #
    12655
    My Garage
    '00 1.8tqm, '90 jeep cherokee
    Location
    northeast

    Re: FMIC install question...

    thats the map sensor, and you need it. get a bung welded onto the coldside pipe thats going to the IM so that you can reconnect that sensor.
    What's AOA? If Audiworld is the 1960's, AOA is 'the man.' Don't try to fight the man, because, just like the hippies, you'll lose.
    Reply With Quote Reply With Quote  
  4. 01-05-2009 01:55 PM #4
    pipe7284
    pipe7284 is offline
    Veteran Member Four Rings pipe7284's Avatar
    Join Date
    Sep 14 2006
    AZ Member #
    11300
    My Garage
    `07 Audi A4 S-Line 6MT Quattro | '01 Audi S4 AVANT 6spd
    Location
    Lansing, MI

    Re: FMIC install question...

    yes, you do need it. there is a flange you need to buy that needs to be welded to the cold side of the FMIC piping.
    '01 Audi S4 6spd Black AVANT DAZ E85 Tune Frankenturbo F21s / 034 RS4 inlets / BOSCH EV4 72# injectors / Walbro 450L fuel pump / Daz 89mm maf housing / AFE Intake Cone / SRM SMICs / 034 street density trans and motor mounts / SSAC downpipes / Vibrant catback exhaust / H&R Ultra Low Coilovers / 18x9.5 Rota Grids / 17z Brembo front BBK / 034 Rear BBK / JHM Short shifter / JHM stg 3 clutch / PODI Boost gauge / [/CENTER]

    SOLD
    Reply With Quote Reply With Quote  
  5. 01-05-2009 02:31 PM #5
    Seerlah
    Seerlah is offline
    Veteran Member Four Rings Seerlah's Avatar
    Join Date
    Dec 05 2007
    AZ Member #
    23104
    Location
    A place between here and there

    Re: FMIC install question...

    To eleborate on the above mentioned, here is a link http://www.034motorsport.com/product...ducts_id=13140
    Reply With Quote Reply With Quote  
« Previous Thread | Next Thread »

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules



    © 2001-2024 Audizine, Audizine.com, and Driverzines.com
    Audizine is an independently owned and operated automotive enthusiast community and news website.
    Audi and the Audi logo(s) are copyright/trademark Audi AG. Audizine is not endorsed by or affiliated with Audi AG.