*** Wheel Stud and Nut Kit ***

**Wizard-of-OD** · 09-24-2008 11:18 AM

Tired of hitting the inside of your wheels against the rotors?I know I am....

Wheel nut and stud combo, M14x1.5 threads, Grade 8.8 with Zinc plating. Supplied in 2 lengths, default is 1.75" (which is fine for most wheel applicaitons w/o a spacer), or 2.5" which would accomodate a spacer. Fits many Audi application with M14 threaded hubs, cone seat for most aftermarket wheels.

For 1.75" stud, lower threads are .4" (10mm) long, upper threads are 1.2" (30mm) long

For 2.5" stud, lower threads are .4" (10mm) long, upper threads are 1.7" (43mm) long

Price for STUDS + CONE SEAT NUTS = 79US SHIPPED
Price for STUDS + BALL SEATS NUTS = 88US SHIPPED

Send me a Private Message when you are ready to order.
Thank You!

**onemoremile** · 09-24-2008 11:21 AM

Excellent offering Issam. I was just thinking about this today.

Got a price for a set of long studs with both sets of nuts? That way I'm prepared for just about anything.

**Wizard-of-OD** · 09-24-2008 11:24 AM

Jim,
the standard set up is 3.50/combo
you add an extra $0.45 for the ball seat nuts.
Send me a PM :D

**onemoremile** · 09-24-2008 12:57 PM

So 97 shipped? Not too bad.

**urban96** · 09-24-2008 02:36 PM

wish you guys were offering these 2 weeks ago

**B518T** · 09-24-2008 03:23 PM

so, what size spacers will the 2.5" accomodate...I am thinking of either going 10 or 15mm...

TIA

**onemoremile** · 09-24-2008 03:29 PM

Originally Posted by B518T

so, what size spacers will the 2.5" accomodate...I am thinking of either going 10 or 15mm...

TIA

They are 3/4" longer so 15-20mm shouldn't be a problem.

**Das General** · 09-24-2008 03:31 PM

Do OZ SL's use ball or cone seats?

**mike-2ptzero** · 09-24-2008 03:38 PM

Originally Posted by onemoremile

They are 3/4" longer so 15-20mm shouldn't be a problem.

How do you get that? It isn't like other people havent been selling the same exact length stud and they only suggest up to 8mm spacer.

The stud only has a outer thread of 1.7", that means the area that the spacer and wheel will sit on is just over 1.7".

**onemoremile** · 09-24-2008 03:42 PM

Originally Posted by mike-2ptzero

How do you get that? It isn't like other people havent been selling the same exact length stud and they only suggest up to 8mm spacer.

The stud only has a outer thread of 1.7", that means the area that the spacer and wheel will sit on is just over 1.7".

Strange. 3/4" is 19.05mm. So the longer studs just end up protruding from the nut more?

**mike-2ptzero** · 09-24-2008 03:51 PM

Originally Posted by onemoremile

Strange. 3/4" is 19.05mm. So the longer studs just end up protruding from the nut more?

Correct.

Here is a picture of the 2.5" long studs I have on my car, this is with OZ wheels and no spacer. Been running them on my car for over 3 years.

**Wizard-of-OD** · 09-24-2008 04:41 PM

All PM's replied

**B518T** · 09-24-2008 04:48 PM

so I wont be able to go with anything larger than an 8mm?

doesnt look like there is much thread left on mikes set-up without spacers :(

**Poopie** · 09-24-2008 07:12 PM

the oz wheels require lugs that are about 10mm longer then stock from what i remember. I had 10mm spacers on my wheels and they looked like mikes set up with 2-3 threads past the nuts. I have the "man set" from mike.

**mike-2ptzero** · 09-24-2008 08:56 PM

Originally Posted by B518T

so I wont be able to go with anything larger than an 8mm?

doesnt look like there is much thread left on mikes set-up without spacers :(

Well every wheel is going to have a different thickness. Best to measure from the back of the wheel to the top of the nut with it in the hole.

**Wizard-of-OD** · 09-25-2008 12:52 AM

Mike what nuts are those on your studs?

**mike-2ptzero** · 09-25-2008 08:32 AM

Originally Posted by Issam@034

Mike what nuts are those on your studs?

Ball seat.

**onemoremile** · 09-25-2008 09:07 AM

Must be the thickness of the OZ wheels. My BBS had a much shorter bore.

A lot of track tech inspections require that there are a few threads showing through open nuts.

**mike-2ptzero** · 09-25-2008 09:19 AM

Originally Posted by onemoremile

Must be the thickness of the OZ wheels. My BBS had a much shorter bore.

A lot of track tech inspections require that there are a few threads showing through open nuts.

Same with drag racing when the car runs so fast. I wish I could find some that were longer but the only ones I can find that are longer have to be installed from the back of the hub.

**Wizard-of-OD** · 10-12-2008 07:41 PM

All PM's replied to.

**bassed** · 10-13-2008 09:33 AM

I was not able to runmy 8mm spacers and 2.5" studkit with my OZ UL's and chance of a 3" stud?

**mike-2ptzero** · 10-13-2008 10:18 AM

Originally Posted by bassed

I was not able to runmy 8mm spacers and 2.5" studkit with my OZ UL's and chance of a 3" stud?

I dont know anyone that produces a 3" thread in stud, the longer ones have to be installed from the back of the hub. This means removing and drilling out the hubs to install them.

**bassed** · 10-13-2008 10:43 AM

Originally Posted by mike-2ptzero

I dont know anyone that produces a 3" thread in stud, the longer ones have to be installed from the back of the hub. This means removing and drilling out the hubs to install them.

I figured that:( No spacers just gets by, I think they change the hole depth from the SL to the UL.

**lotusgardener** · 10-13-2008 10:55 AM

what kind are those pictured? cone?

**mike-2ptzero** · 10-13-2008 11:12 AM

Originally Posted by bassed

I figured that:( No spacers just gets by, I think they change the hole depth from the SL to the UL.

Have you tried running 5mm spacers?

**onemoremile** · 11-26-2008 03:13 PM

I installed a set of the long studs last night along with black TSW Hockenheims and snow tires. Nice stuff.

**Wizard-of-OD** · 11-27-2008 01:52 AM

Originally Posted by onemoremile

I installed a set of the long studs last night along with black TSW Hockenheims and snow tires. Nice stuff.

Thanks Jim

**JumboBlack1.8** · 11-27-2008 11:40 AM

I've got an 034 store credit, and I can't decide if I wanna get these or Street Density mounts........these look like really good quality

**Wizard-of-OD** · 11-28-2008 02:48 AM

PM Replied :D

**onemoremile** · 11-28-2008 06:39 PM

You've got 3-4 threads showing. My TSW Hockenheims (Merc fitment) only have 1-2 showing. The short studs just wouldn't have worked at all.

Originally Posted by mike-2ptzero

Correct.

Here is a picture of the 2.5" long studs I have on my car, this is with OZ wheels and no spacer. Been running them on my car for over 3 years.

**mike-2ptzero** · 11-28-2008 09:59 PM

Originally Posted by onemoremile

You've got 3-4 threads showing. My TSW Hockenheims (Merc fitment) only have 1-2 showing. The short studs just wouldn't have worked at all.

Well the shorter set are really only good for the stock wheels, even 034 states that on their site. Most people are going to end up ordering the longer set seeing that they will work for stock and aftermarket wheels.

**Wizard-of-OD** · 12-03-2008 09:00 PM

All PM's replied.Have not forgotten you Jim :D

**ShawFM** · 12-07-2008 04:47 PM

I think I am ready! Long studs + ball seat. Saves the hassle with the winter and summer wheels & having to keep changing bolts when I put the spacers back on for the winter wheels.

**Wizard-of-OD** · 12-09-2008 09:17 PM

Send me a PM :)

Thread: * Wheel Stud and Nut Kit *

Thread Tools

Display