A.W.E. Tuning 2.7T Downpipes

[Alex/AWE]

Our 2.7T Downpipes with Test Pipes are In Stock and Ready to Ship today!

These downpipes are a must for 2.7T enthusiasts looking to maximize engine performance. They will allow your car to really breathe and perform how it should!

This direct fit replacement for the stock downpipes consists of 2.5" diameter (63.5mm) T304 stainless steel downpipes (they taper from 3" to a real 2.5"), CNC cut flanges and brackets, and Aeroquip flex joints. All welds are TIG welded and finished (all of the internal welds are smooth, where it matters most) and the all the bends are mandrel.

The Entire Downpipe Kit:




Smooth Transitions



Proven Results:


Graph of measured differences between baseline and test in dyno sheet of AWE Tuning 2.7T downpipes vs. Stock. AWE Tuning 2.7T downpipes produced a peak increase of 11.7 ftlbs at 3750 rpms and an increase of 8.3 hp at 5500 rpms to the wheels vs. the stock downpipes. Notice, however, that at ~3000 rpms, AWE Tuning downpipes produced a 17 ftlbs increase, and at 6250 rpms a 24 hp increase. That's ~15 ftlbs and 31hp gains at the crank!




If you would like to learn more about our 2.7T Downpipes, please call or email us.

[email protected] or 1-888-565-2257

You can also go directly to our website. Here is a link:
http://www.awe-tuning.com/pages/shar...&IL=AWESflo_DP

If you have any questions you would like to ask, please feel free. I will do my best to answer them.

[Daft]

Ohhhhhh. Those are nice.

If I only had the money.... I'm still saving up after my Intercooler purchase from AWE.

Eitherway, do you have the variety of versions of these to fit the different downpipes of the A6?

The 2000-2002 APB motors are separated by manual and tiptronic but, the BEL motors (2003+) have different downpipes as well.

If you have a BEL manual car, the pipes are differently shaped than a 2002 APB and the BEL tiptronic car is even slightly changed from that as well.

[beckmaster]

how much with install?

[wofman]

OK - so let's say we start with AWE downpipes. How different from using other versions? If we start with these downpipes what is best (performance) after that, without getting "too loud". Freer flowing cats? Resonators/mufflers, etc.? Why are x pipes used? What if piggies are just gutted and go from there? There seem to be as many approaches here as there are colors for Audis. Isn't this a tad more costly than other solutions?

[chrisbostonusmc]

so are the A6 and s4 ones identical to each other or is the design different?

[stevea6/z28]

lot of money for not alot i just gutted my stockers cant see spending that kind of money and who needs bling underneath no ones gunna see most of it.Not to be a dick but if giac's chip was $1600 with out labor for 8hp and 11ftlb how many people would buy it.But they are nice

[ritzblitz]

Yeah they definitely look well made. I guess these fit both S4 and A6? How hard are they to install?

[wofman]

S4 is not the same

[audirs]

s4 downpipes are different then a6. you can modify certain s4 downpipes to work though. cant speak on the awe stuff, maybe they do work.

[Alex/AWE]

Ohhhhhh. Those are nice.

If I only had the money.... I'm still saving up after my Intercooler purchase from AWE.

Eitherway, do you have the variety of versions of these to fit the different downpipes of the A6?

The 2000-2002 APB motors are separated by manual and tiptronic but, the BEL motors (2003+) have different downpipes as well.

If you have a BEL manual car, the pipes are differently shaped than a 2002 APB and the BEL tiptronic car is even slightly changed from that as well.

Our downpipes will fit all 2000-2004 2.7T A6s equipped with manual transmissions. We do not have versions for tiptronic cars at this time.

how much with install?

PM Sent! We charge 8 hours of labor for the installation of these downpipes.

How different from using other versions?

Do you mean what are the differences between our downpipes and other manufacturers downpipes?

If we start with these downpipes what is best (performance) after that, without getting "too loud". Freer flowing cats? Resonators/mufflers, etc.? Why are x pipes used? What if piggies are just gutted and go from there? There seem to be as many approaches here as there are colors for Audis. Isn't this a tad more costly than other solutions?

Why don't you pm me your email address and I will happily answer all these questions for you.

[wofman]

email sent - thanks

[stevea6/z28]

8 hours for labor, lol i can pull the motor and tranny in 2 by myself 5 hours maybe still $2500 plus tax no thanks.not any difference in power that your gunna even come close to fealing.(8 hp 11 ftlb)