DIS Coding Help Please

[rapidman123]

Hi There, I have a 2007 S Line that came without DIS so have fitted the new stalk and tried to code it with VagCom but the Bulb Check keeps coming up and bleeping at me!! All my bulbs are working fine, I think I may need some help with the coding, Can anyone help me please?

[a4audi4fun]

Hi There, I have a 2007 S Line that came without DIS so have fitted the new stalk and tried to code it with VagCom but the Bulb Check keeps coming up and bleeping at me!! All my bulbs are working fine, I think I may need some help with the coding, Can anyone help me please?

What coding do you have for Instruments (Module 17) and adaptation channel 19 as well.?

Why not put up a scan of everything and we can try and help you out. I have had a retrofit done for a 2008 B7 S-Line so know what settings worked for me.

[rapidman123]

Thanks for the reply, I did read your post and it was helpful. I will try to post them shortly. Thanks Again.

[rapidman123]

Right, Instruments Module 17 is 0006418 and adaptation on 19 is 31000.

[a4audi4fun]

Your codes seem consistent given that you are in GB and I'm in Canada. Try adaptation code 31300 and see if the menu display gives you any additional options. I found I needed to have the engine running in order to get the menu display; the reset button on the bottom of the stalk moves you through the high level options and the toggle switch on the end lets you make a choice.

[SEXICÄN]

excuse my ignorance, what is DIS

[rapidman123]

It is the Display on the dash showing MPG, driving time etc....

Thanks A4Audi4Fun, I shall give that a try later.

[rapidman123]

I just thought I should mention, I am trying to do the coding with a cheap lead and Vag com 704, not sure if that is important or not??

[a4audi4fun]

From experience, I know the $7 cable had limits on what adaptation channels I could adjust; obviously the Ross-Tech cable I now have works great :-) :-)

[pakratt99]

Mind if I ask where you got your stalk from and how much it ran you? Looking to do the mod myself.

[rapidman123]

Have just been looking into my problem here and can update that the display is saying a problem with the "Parking Lights" and "Dipped Headlights" not bulb warning as I stated previously... Maybe this changes things???

[rapidman123]

Here's a copy of the scan with faults if that helps anyone try to help me: Monday,16,June,2008,20:40:27:59303
VAG-COM Version: Release 704.1
H
Address 09: Cent. Elect.
Control Module Part Number: 8E0 907 279 M
Component and/or Version: int. Lastmodul ECE 0907
Software Coding: 00001
Work Shop Code: WSC 06325
4 Faults Found:

01494 - Bulb for Parking Lamps; Left (M1)
30-00 - Open or Short to Plus
01498 - Bulb for Parking Lamps; Right (M3)
30-00 - Open or Short to Plus
00978 - Lamp for Low Beam; Left (M29)
30-00 - Open or Short to Plus
00979 - Lamp for Low Beam; Right (M31)
30-00 - Open or Short to Plus
---------------------------------------

[a4audi4fun]

I set mine to 11021 to have Bi-Xenon in Rest of World mode to adjust the parking lights. It came from the factory as 11023 - Avant for Canada with Bi-Xenon and DRL. I suspect correct setting of the halogen/bi-xenon config will clean up your fault codes.

C00,Central Electronics (J519) Coding
C01,?xxxx: Chassis
C02,0 = Limousine (PR-K8B)
C03,1 = Avant (PR-K8D)
C04,2 = Cabriolet (PR-K8K)
C05,x?xxx: Driving Light Switch
C06,0 = Rain/Light Sensor (G397) not installed (PR-8K0/8K1/9C6/8K4)
C07,1 - Rain/Light Sensor (G397) installed (PR-8K3/8K7/9C7/8K9)
C08,xx?xx: Trailer Hitch
C09,0 = Trailer Hitch not installed (PR-1D0)
C10,1 = Trailer Hitch installed (PR-1D2)
C11,xxx?x: Headlights
C12,0 = Halogen Headlights w/o Daytime Running Lights (PR-8Q0/8Q1+8K0/8K7)
C13,1 = Halogen Headlights with Daytime Running Lights (PR-8Q0/8Q1+8K1/8K3/9C6/9C7)
C14,2 = Bi-Xenon Headlights with Daytime Running Lights (PR-8Q3/8Q5+8K9/8K4)
C15,3 = Bi-Xenon Headlights w/o Daytime Running Lights (PR-8Q3/8Q5+8K0/8K7)
C16,4 = Bi-Xenon Headlights with Daytime Running/Tail/License Plate Lights (PR-8Q3/8Q5+8K1/8K3)
C17,xxxx?: Country
C18,1 = Rest of World/Nordic Countries/Denmark/Croatia/Baltic Countries with Bi-Xenon
C19,2 = Nordic Countries/Denmark/Croatia/Baltic Countries without Bi-Xenon
C20,3 = USA/Canada with Bi-Xenon
C21,4 = Canada without Bi-Xenon
C22,5 = Special Vehicles

[rapidman123]

It will not let me change them, I can get in to it but it will not save the new code????

[a4audi4fun]

Sorry don't think I can suggest much more; could be a cable problem or a module problem if the changes won't stick.

[rapidman123]

Ok thanks for your help anyway. I am gonna have to try takin it in to Audi.....

[a4audi4fun]

It will not let me change them, I can get in to it but it will not save the new code????

BTW - did this occur when trying to change the adaptation channel 19 setting; that was the symptom I had with my ebay cable; once I got my Ross-Tech cable that change worked fine

[rapidman123]

I finally found the problem today!!!! My aftermarket zenons were causing the Low beam warning and the sidelight bulbs had gone and were causing the Parking light warning......

I wish I'd realised this sooner.. Thanks for the help I got.....

I can't believe I didn't check the basics!!