Stage 2 EPL 4 gallons E85 and 1000cc methanol does 418 awhp on dyno!

[evil35r]

So finally got to the dyno 418 awhp and 404 awtq. Going to track next Friday hoping for the stage 2 record. Mods in sig.
https://preview.ibb.co/fAmTPy/620_F2814_0_A98_484_B_AA5_A_CAAB9_BA0_A96_B.jpg


https://youtu.be/U-UV2tlY4LM

[street2gen]

So finally got to the dyno 418 awhp and 404 awtq. Going to track next Friday hoping for the stage 2 record. Mods in sig.
https://preview.ibb.co/fAmTPy/620_F2814_0_A98_484_B_AA5_A_CAAB9_BA0_A96_B.jpg


https://youtu.be/U-UV2tlY4LM

You did this at near 90 degrees correct? Wonder how much of a difference you would see if you were on a hx instead of the meth.

[evil35r]

Yea ambient was 88 da 1600. All I have for cooling is the pump mod and the meth/water. This was our 4th pull the other 3 were 410-415. Started with spray comming on at 8 maxing at 14 I dialed it to 7 and 11 and got the most power the pull before I did 6 and 9 and it lost a little power so I stuck with the 7 - 11 setting for methanol. If I were on hx not sure if it would help much maybe a little. I’d go dual pulley but then I’d have to get cooling mods plus a new file and she’s a beast right now don’t wanna mess with her besides wheels and springs and I’ll be done.

[Phil.Lmbrt]

Where do you inject if it is not too much asked?

Thanks !

[VeeDubbinJetta]

I’m on tapatalk so I can’t see your sig, what file was this on? Very nice numbers [emoji1303]

[evil35r]

700cc nozzle inch away from tb. 300cc nozzle a inch up from the air filter.

Stage 2 meth/93 7th revision worked with tony for months before we got her perfect. Shout out to Tony for all the help. 28 degrees of timing 😂

[Acejam]

I’m on tapatalk so I can’t see your sig, what file was this on? Very nice numbers [emoji1303]

Tap the persons username and it will pull up their profile, displaying their signature. [emoji106]


Sent from my iPhone using Tapatalk

[Morritse]

this is extremely impressive, most powerful single pulley car I've seen.

[evil35r]

this is extremely impressive, most powerful single pulley car I've seen.

Thanks!!!!

[Morritse]

Thanks!!!!

I made 410 dual pulley e40, does meth really help that much? :O

[evil35r]

not sure I think it’s all in how much timing you can safely run while keeping iats down.. even at dual pulley levels you get more boost yes but more heat. I’ve given her all she has with a single pulley setup only thing I can do more is port and polish the supercharger and get a bigger th but then I’m at what 430 or so maybe more for power so not sure if it’s worth it. If I get the stage 2 record I’ll stay king until I get dethroned lol and then do more but I’ll stay single pulley most likely. It def would be fun to see how fast I could make her go though and go dual pulley etc but not sure if it’s worth it for my daily

[Fresh.S4]

im still flabbergasted that its recommended to run such a big nozzle that close to the tb. learning about spraying with turbo's it was always the opposite and running the bigger nozzle further down track. Im wondering if its because theirs no maf to mess with that makes it ok. OR its seriously that hot inside the box that spraying that much makes it evaporate stupidly fast lol...

[evil35r]

Stupidly fast figure turbo cars have air to water coolers and the turbo gets spun by exhaust gases. Our cars don’t have any of this but a coolant loop the intake gets stupid hot. I’ve read and read and read and how I have it it is the best possible scenario. When running just the 700 nozzle I never got bogged even if I ran it at 1 lb of boost adding the second 300 nozzle near the air filter I got bogged down when I started the meth too low and slowly brought it to where it wouldn’t bog aka quench... so the most meth mixture I can possbley spray I am spraying now. It’s different for us roots guys. Even my buddy with a terminator runs similar to me and he has almost 1k hp.

[evil35r]

Also Matty has almost the same setup

[BDP]

28 degrees of timing 😂

Just curious what do most "race files" request for timing? Isn't generally what separates octane specific files the timing?

[kelseysautobody]

Awesome results! Now just need to get a clean pass or two in at the drag strip. In decent conditions I think it has a 120+ mph pass in it.

[evil35r]

Here’s another pull video


https://youtu.be/BE9IyqOZars

[evil35r]

Heading to the track! Wish me for records!!!!

[evil35r]

Spinning some best 60’ still a 1.7 but got a 11.8 @ 116!!! Gonna keep going for the record!

[Thurston]

really strong power numbers, nice 1/4 mile run too !

[evil35r]

https://youtu.be/IzeXeehLjUQ

https://youtu.be/ZBmHKPLk8m4

[rgpwr]

Would have loved to see the other drivers face 😆