Introducing JHM B7 A4 2.0T 3" Test Pipe and High Flow Cat!

[Jake@JHM]

Hey everyone!

Finally, a no-compromise, performance-first 3" Test Pipe and High Flow Cat for the B7-A4 2.0T!!! If you are looking to get the most performance out of your stock turbo B7-A4 2.0T, this is the test pipe/HFC that you need!

http://www.jhmotorsports.com/products/pictures/B7A4/JHM-B7-A4-20T-Catless-Test-Pipe.jpg

http://www.jhmotorsports.com/products/pictures/B7A4/JHM-B7-A4-20T-Cat-pipe.jpg

http://www.jhmotorsports.com/products/pictures/B7A4/JHM-B7-A4-20T-Catless-Test-Pipe-turbo-flange-detail.jpg

This is the same Test Pipe that we ran in our JHM 2.0T when we set the fastest stock turbo quarter mile record: 13.38 seconds at 100.3 mph! (see video below)


http://youtu.be/mbVOHMNRSnA

INFORMATION ON THE B7-A4 2.0T EXHAUST SYSTEM:

After the turbo on the B7-A4 2.0T there are 3 different components in the exhaust system:

- TEST PIPE or CAT PIPE (OEM Cat Pipe): This pipe is the shortest section of the exhaust system and can be seen from the top of the car. It attaches to the turbo outlet and in stock form, contains the OEM Catalytic Converter. There are two oxygen sensors located on this pipe - one right after the turbo outlet and one after cat. After the cat, this pipe bends down to connect to the next part of the exhaust system, the CAT-BACK which includes the DOWNPIPE and the REAR EXHAUST.
CAT-BACK:

- DOWNPIPE: This section of the exhaust attaches to the cat pipe and runs down from that connection over the CV shaft then under the passenger side of the transmission cross-member. In the stock formation, it connects to the REAR EXHAUST via a slip fit clamp where the end of the DOWNPIPE slips over the REAR EXHAUST. (Stay tuned for our JHM Downpipe-Y Adapter to mate to a B6-B7 S4 Catback!)

- REAR EXHAUST: This final piece of the exhaust system is connected to the back of the DOWNPIPE and in the stock configuration splits into two pipes after exiting a resonator. After the resonator, the pipes continue to go apart and then lead into a muffler on each side. At the exit of the muffler, the REAR EXHAUST ends with the tips that you can see at the back of your car. Sometimes this section of the exhaust is mistakenly called the "cat-back". On the B7-A4 2.0T, a cat-back exhaust would replace BOTH the DOWNPIPE and the REAR EXHAUST sections. Most quality exhaust manufacturers sell true "cat-back" exhausts that will bolt up to your OEM cat-pipe or your test pipe. However, we have found that a number of manufacturers making exhaust products for the B7-A4 2.0T will market a rear exhaust system as a cat-back. Use this information to make sure you know what exhaust components you are replacing.

THE JHM DIFFERENCE:

The JHM B7-A4 2.0T 3" Test Pipe/HFC starts with nearly a 3 and a half inch opening at the turbo outlet! The outlet on the stock K03 turbo is 3.15 inches, so if we were to go with only a 3" inch opening on the pipe, we'd already be choking off the turbo! We opened up our pipe to the OEM Turbo to Cat Pipe gasket size which is actually slightly bigger than the OEM catalytic converter inlet.

http://www.jhmotorsports.com/products/pictures/B7A4/JHM-B7-A4-20T-Catless-Test-Pipe-turbo-flange-detail-1.jpg

We also give our test pipe the largest downpipe connection possible while still maintaining strength in the connecting flange. This pipe is NOT like other test pipes out there which can neck down to the stock downpipe flange size. We make our outlet piping size as close to 3" as possible while still allowing it to hook up to whatever downpipe setup you currently have on your car. This leaves you room to grow into more powerful exhaust setups or just hook to your current stock downpipe. We maintain the stock bolt pattern but manufacture a custom flange that is opened up to receive our nearly 3" piping. Though this method **slightly** limits the size of pipe we can run at the outlet, we decided to put our piping inside the flange because it's a stronger way to build the flange connection while still allowing the test pipe/HFC to bolt up to both stock and other downpipes on the market.

http://www.jhmotorsports.com/products/pictures/B7A4/JHM-B7-A4-20T-Test-Pipe-TP-to-DP-flange.jpg

The catalytic converter used in the JHM Cat Pipe is a high-quality, 300-cell, high-flow race cat. We locate it as far away from the turbo outlet as possible. While this made it a more difficult piece to fabricate and produce, we felt that it was the only way to do it since putting a restriction right against the back of the turbo would restrict airflow

Finally, our Test Pipe/HFC features a J-bung for the secondary oxygen sensor. We've been working with several different configurations on this piece to get just the right setup for the B7-A4 2.0T. With our J-bung, not only will you be Check Engine Light free (for catalyst efficiency codes), but because of the way we've located it on the pipe, you'll also have easy access to the secondary oxygen should you ever need to replace it!

http://www.jhmotorsports.com/products/pictures/B7A4/JHM-B7-A4-20T-Test-or-cat-Pipe-j-bung-detail.jpg

For those customers interested upgrading to our JHM 3" Test Pipe/HFC who already have a larger downpipe (or are looking to buy our JHM Y-Adapter) we offer a no compromise gasket and hardware kit. When replacing your OEM cat-pipe with our JHM Test Pipe, you'll most likely need to replace the gasket at the cat-pipe to downpipe connection. Most companies just provide a stock gasket for this connection which has an inner diameter of 2.3". Not only is the JHM gasket that we include in our hardware kit made out of aluminum but it also features an inner diameter of 2.8" - the largest possible diameter while still maintaining the stock bolt pattern. To purchase this hardware kit, please go back one section and add the item to your cart. You can also search for "JHM 2.0T Hardware Kit" in the search box on the top, right-hand corner on any page on our website.

http://www.jhmotorsports.com/products/pictures/B7A4/JHM-B7-A4-20T-Test-cat-pipe-hardware-kit-detail.jpg

For more information on the JHM B7 A4 3" Test Pipe, Click Here! (http://jhmotorsports.com/shop/catalog/exhaust-test-pipe-jhm-catless-test-pipe-for-b7-a4-20t-p-1852.html) Or if you would like more on our JHM B7 A4 3" HFC, Click Here! (http://jhmotorsports.com/shop/catalog/exhaust-cat-pipe-jhm-high-flow-cat-hfc-for-b7-a4-20t-p-1893.html) Both options are in stock and ready to ship!

If you have any questions, please feel free to ask!

Jake

[JPS]

Bad ass. Going to have to get one come spring time.

Sent from my SCH-I605 using Tapatalk

[Jake@JHM]

Bad ass. Going to have to get one come spring time.

Sent from my SCH-I605 using Tapatalk

Yeah definitely!

Also stay tuned for the JHM Downpipe-Y Adapter! (non neck-down will be an option to use aftermarket B6-B7 S4 exhaust as well)

http://jhmotorsports.com/products/pictures/B7A4/JHM-20T-y-pipe-adapter-b6-b7-s4-cat-back-detail-web.jpg

Jake

[Jake@JHM]

Wow, wasn't expecting that many orders right off the bat! Thanks again for your support everyone. [up]

Jake

[mec]

Jake,

I consider myself to be an unbiased hardcore evaluator and I can't play favorites because I own a few of your products already. The importance of staying objective and looking at a product to spot pros and cons is undoubtedly the best skill that we could ask for when reviewing a product. And while I can tell you guys put some design into this product, many hours of labor, parts sourcing, sweat, tears, I have to ask just one thing.....







































http://newspaper.li/static/575c07380ca151d639bc1e2a4b0f35cd.jpg

[Jake@JHM]

LOL!!!


There is only one way to find out!

[Jake@JHM]

Thanks for the orders so far guys! [up]

[teckk]

You wouldnt happen to be related to jake from state farm would you ? O.O

[Jake@JHM]

You wouldnt happen to be related to jake from state farm would you ? O.O

This was once made for me:

http://gickr.com/results3/anim_53375ee2-e774-1c64-399a-06917c34114d.gif

[teckk]

Thats awesome lmaoo Was the car ever fixed ? 'Scared & anxious little kid voice'

[Jake@JHM]

Of course!

[teckk]

Haha i want whatever you gave him pronto , when are your downpipes gonna be available ?

[Jake@JHM]

I can sell the DP-Y to you now if you are 6mt, but we are waiting for a local Tip customer to confirm fitment before we officially release it.

Jake

[Jake@JHM]

Alright guys,

As promised here is the exhaust video!


http://youtu.be/VAf5ycU6Kto

JHM 3" Test Pipe
JHM 3" Downpipe- Y Adapter
JHM/FI 2.5" B6 S4 Catback (Resonated)

I am now currently running the the non resonated version.

Jake

[a4life93]

PM Me pricing on the testpipe and that Y-Pipe!

[AKO]

How much with the price on the Exhaust be?

[Jake@JHM]

PM's sent!

Thanks for the orders so far guys!

[drumnjuny]

will it blend!!!

+1 for JHM for adding to our list of options. Can't wait till you guys start putting new stuff (ehm ehm, BT kits) out on the market [up]

[Jake@JHM]

will it blend!!!

+1 for JHM for adding to our list of options. Can't wait till you guys start putting new stuff (ehm ehm, BT kits) out on the market [up]

Thanks! The plan is to throw some JHM style into the B7 A4 platform and start building the recipe to making some fast cars!

Jake

[Jake@JHM]

Woot! More orders going out! Thanks again guys!

[Jake@JHM]

More orders going out! Thanks again everyone.

[Jake@JHM]

Bump!

We have these stocked and ready to ship!

Jake

[b0i]

Send me a PM on pricing for the Downpipe-Y Adapter please, I think I'm about to pull the trigger on your test pipe soon. After hearing JHM>RAI my choice seems pretty clear!

[Jake@JHM]

Send me a PM on pricing for the Downpipe-Y Adapter please, I think I'm about to pull the trigger on your test pipe soon. After hearing JHM>RAI my choice seems pretty clear!

PM Sent!

[drumnjuny]

you would be insane to buy anything from RAI after hearing anything about Axis or my stories, or read about the fitment problems they've had especially for B7s. i should show you the 3/4" thick ghetto welds on my front mount. it looks like my dog did it. and she doesn't even have hang nails let alone opposable thumbs

[NolanB7]

Jake can you give me a price on the HFC and the down pipe? Also does Jhm sell the b6-b7 S4 exhaust? Thanks!

[Jake@JHM]

Jake can you give me a price on the HFC and the down pipe? Also does Jhm sell the b6-b7 S4 exhaust? Thanks!

Yeah! You can find our 3" HFC Pipe HERE (http://jhmotorsports.com/shop/catalog/exhaust-cat-pipe-jhm-high-flow-cat-hfc-for-b7-a4-20t-p-1893.html) for $395 and our DP-Y will intro at $495.


Depending on what DP-Y you choose, you can either run any aftermarket 2.5" Cat back for a B6-B7 S4 ( We recommend the JHM/FI Cat Back HERE (http://jhmotorsports.com/shop/catalog/exhaust-cat-back-jhm-b6-s4-stainless-steel-25-pipe-by-fi-p-384.html)) or a stock B6-B7 S4 cat back that you find on the classifieds for dirt cheap.

The cool thing about the stock s4 cat back is that it flows enough for a 340HP V8 so it is more than enough exhaust for any k03/k04 2.0T.

Jake

[Jake@JHM]

Thanks for the orders guys!

[CLEANA3]

Waiting for the tip down pipe

[Sanjman]

Jake someone is going to ask this if I don't, but what is the purpose of using the flex pipes? Simple to reduce strain on the pipes while through bends etc?

[Jake@JHM]

Jake someone is going to ask this if I don't, but what is the purpose of using the flex pipes? Simple to reduce strain on the pipes while through bends etc?

Yes, the big one is to help with the pipe shifting around while it gets hot or cold, and the bottom one that is on the Y is for the each of fitment onto the S4 catback!

[Jake@JHM]

More Test Pipes and HFCs out the door! Thanks guys! [up]

[M1GHTYHEALTHY]

Sounds like the test pipes are currently OOS. HOWEVER, Drew made it happen. Thanks again!

Now FedEx can't arrive soon enough...

[Jake@JHM]

Sounds like the test pipes are currently OOS. HOWEVER, Drew made it happen. Thanks again!

Now FedEx can't arrive soon enough...

Yeah, we usually keep a bunch in stock so there is no down time but everyone has been buying them quicker than we can make them! I saw Dru get up and bring is JHM Test Pipe out to the shipping department [up].

Thanks again for your order!

[vortexjunkie]

Sounds like the test pipes are currently OOS. HOWEVER, Drew made it happen. Thanks again!

Now FedEx can't arrive soon enough...

No worries! I'm glad you will be getting your pipe as soon as you had hoped... Like I said I'm sure I'll manage to find another one. Looking forward to seeing a review.

Dru

[Jake@JHM]

Thanks for the orders everyone! Thanks to all of you who have purchased the DP-Y too! [up]

[Jake@JHM]

More test pipes out the door [up]

[Jake@JHM]

Another batch of Test Pipes and HFCs are made and ready to ship!

Thanks for all of your support guys [up]

[Jake@JHM]

That J-bung though!

[Rastboostin]

Mine's coming on Wednesday, can't wait!

[Jake@JHM]

Mine's coming on Wednesday, can't wait!

I believe I spoke to you over the phone today!

[Jake@JHM]

More orders out the door [up].

Thanks for all of the support guys!

http://global3.memecdn.com/tech-support-is-here-for-you_c_471601.jpg

[Bogdansaudi]

Yeah definitely!

Also stay tuned for the JHM Downpipe-Y Adapter! (non neck-down will be an option to use aftermarket B6-B7 S4 exhaust as well)

http://jhmotorsports.com/products/pictures/B7A4/JHM-20T-y-pipe-adapter-b6-b7-s4-cat-back-detail-web.jpg

Jake

If I were to get the high flow cat you guys sell for the 2.0t, would this downpipe work on it?

Sent from my SGH-I337M using Tapatalk

[ktish]

If I were to get the high flow cat you guys sell for the 2.0t, would this downpipe work on it?

Sent from my SGH-I337M using Tapatalk

Yes.

[Jake@JHM]

Yup!

Sent from my S5

[Chrisw023]

The HFC will be in my near future! Just need to get this timing belt done first.

[RoguesGambit]

Love my HFC and about 2-3 weeks away from ordering the y and the B7 FI exhaust. Can't wait!

[Jake@JHM]

Fresh batch of Test Pipes, HFCs, and Even DP-Ys are made and ready to ship! Thanks again for all of the orders so far guys!

Jake

[RoguesGambit]

Asinine question Jake, could FI make a mufferless B7 S4 Catback?

[Jake@JHM]

Asinine question Jake, could FI make a mufferless B7 S4 Catback?

Yes, but it would be VERY loud. For a few days I ran a customers old FI cat back that had cherry bomb glass packs instead of mufflers and it was crazy loud!

[RoguesGambit]

How loud we talking? Just hate Mufflers and was looking to see what options there were to either get rid of or reduce it?

[Jake@JHM]

How loud we talking? Just hate Mufflers and was looking to see what options there were to either get rid of or reduce it?

Get the regular non resonated setup like I am running now, and if you think it is too quiet have an exhaust shop replace the mufflers with resonators/straight pipe and go from there.

[RoguesGambit]

Sounds like a plan, should be set to order by the middle or end of the month at this rate

[Jake@JHM]

Sounds like a plan, should be set to order by the middle or end of the month at this rate

Sweet! Let me know when you are good to go [up]

[RoguesGambit]

Sweet! Let me know when you are good to go [up]

Will do, blue

[jaycurn]

Just ordered my 3" JHM TP! Awesome service and help along the way from Jake!! [hail]

[PNW Avant]

just ordered my dp y today [wrench]

[Jake@JHM]

Just ordered my 3" JHM TP! Awesome service and help along the way from Jake!! [hail]


just ordered my dp y today [wrench]

Thanks again guys! [up]

[jaycurn]

just ordered my dp y today [wrench]

One step behind ya!!

[RoguesGambit]

Hey Jake, ever get a non-res exhaust vid up?

[Jake@JHM]

Hey Jake, ever get a non-res exhaust vid up?

Bug Dru, the camera man!

[RoguesGambit]

Bug Dru, the camera man!

I will when I get a chance to

[jaycurn]

Got mine today... Looks amazing!!! [drool]
http://i800.photobucket.com/albums/yy289/jaycurn/Cam%20Follower%205-25-14/B1A26248-B8FF-4C87-8AEB-20E193EA3250_zpshrxkkxkt.jpg (http://s800.photobucket.com/user/jaycurn/media/Cam%20Follower%205-25-14/B1A26248-B8FF-4C87-8AEB-20E193EA3250_zpshrxkkxkt.jpg.html)

[Jake@JHM]

Woot!!

Sent from my S5

[swoardrider]

My POS Ecode test pipe just cracked, and I'm tired of switching out the Cat every 2 years for smog. Will the HFC pass the sniffer for Cali smog?

[Jake@JHM]

My POS Ecode test pipe just cracked, and I'm tired of switching out the Cat every 2 years for smog. Will the HFC pass the sniffer for Cali smog?

The HFC is intended for "Off-Road Use Only" However we have had a ton of customers report back that they passed CA Smog (since we use this cat on the S4 and RS4 too).

[swoardrider]

The HFC is intended for "Off-Road Use Only" However we have had a ton of customers report back that they passed CA Smog (since we use this cat on the S4 and RS4 too).

Any idea of the power loss difference on your, TP vs HFC with K03?

Thanks,
Grady

[Jake@JHM]

Any idea of the power loss difference on your, TP vs HFC with K03?

Thanks,
Grady

To be honest you would notice a sound difference before a performance difference. We use a very high quality HFC that flows very well.

Jake

[Jake@JHM]

For those of you looking to go with our DP-Y, this guy has our Quad Tip S4 exhaust for sale in the classifieds!

http://www.audizine.com/forum/showthread.php/600451-For-Sale-B7-A4-S4-Parts

[filou]

For those of you looking to go with our DP-Y, this guy has our Quad Tip S4 exhaust for sale in the classifieds!

http://www.audizine.com/forum/showthread.php/600451-For-Sale-B7-A4-S4-Parts


Nice catch. I sent him a pm. If I end up getting it, I might have to place an order for some DP-Y sooner than I thought!

[Jake@JHM]

Nice catch. I sent him a pm. If I end up getting it, I might have to place an order for some DP-Y sooner than I thought!

Haha Hopefully you get it!

Jake

[Jake@JHM]

Thanks for the orders everyone! More in stock and ready to go!

[Jake@JHM]

TTT!

[PNW Avant]

Ok...here's a video finally. I need more practice at this. I was pretty timid to leave my camera alone, and to drive too fast. I'll try to make some better ones soon.

It sounds less farty in person, I think.


https://www.youtube.com/watch?v=jZX5gOstGHo&feature=youtu.be

[oshburg]

Ok...here's a video finally. I need more practice at this. I was pretty timid to leave my camera alone, and to drive too fast. I'll try to make some better ones soon.

It sounds less farty in person, I think.


https://www.youtube.com/watch?v=jZX5gOstGHo&feature=youtu.be


Sounds good thanks for posting. Test Pipe or just Downpipe and S4 Cat Back?

[jaycurn]

Took the first couple of drives with my 3" TP yesterday and I will definitely say VERY nice! Def a little more pep across the entire power band and noticeable low end torque improvement! Can't wait to get the DP-Y installed!

[PNW Avant]

Sounds good thanks for posting. Test Pipe or just Downpipe and S4 Cat Back?

OEM Cat, DP, and S4 catback.

[Jake@JHM]

Sweet video! Thanks for posting!

[jaycurn]

Ok...here's a video finally. I need more practice at this. I was pretty timid to leave my camera alone, and to drive too fast. I'll try to make some better ones soon.

It sounds less farty in person, I think.


https://www.youtube.com/watch?v=jZX5gOstGHo&feature=youtu.be

Sounds great! Hope to have a similar video up soon + TP. [drool]

[Jake@JHM]

Thanks for the orders everyone!

[PNW Avant]

Thanks for the orders everyone!

No Jake, thank you.

[Jake@JHM]

New addition to the JHM Test Pipe!

http://img.tapatalk.com/d/14/07/05/are4y6y4.jpg

[rongeur]

still time to add one to previously purchased?

[Jake@JHM]

still time to add one to previously purchased?

We can definitely throw that on for you if you want to bring it to us!

[Jake@JHM]

Thanks for the orders guys!

[Jake@JHM]

Thanks for the orders everyone!

Don't forget to check out our JHM DP-Y!

http://jhmotorsports.com/shop/catalog/images/JHM-B7-A4-20t-y-pipe-300.jpg

Manual and CVT Transmissions: http://jhmotorsports.com/shop/catalog/exhaust-downpipe-jhm-to-25-for-b6-b7-s4-cat-back-on-b7-a4-20t-manual-cvt-p-1946.html

Tiptronic Transmission: http://jhmotorsports.com/shop/catalog/exhaust-downpipe-jhm-275-to-25-for-b6-b7-s4-cat-back-on-b7-a4-20t-auto-tip-p-2190.html

[CLEANA3]

Still love the set up , just need the tune now

[Jake@JHM]

Thanks for the orders guys [up]


Still love the set up , just need the tune now

The 07 and 08 files will be ready here shortly!

[Peckn4]

Thanks for the orders guys [up]



The 07 and 08 files will be ready here shortly!
So very excited!!!

[Jake@JHM]

So very excited!!!

Me too!

[Jake@JHM]

If you are looking for the best performing, highest flowing exhaust setup on the market, look no further!

http://www.jhmotorsports.com/products/pictures/B7A4/JHM-B7-A4-20T-Catless-Test-Pipe.jpg

http://jhmotorsports.com/shop/catalog/exhaust-test-pipe-jhm-catless-test-pipe-for-b7-a4-20t-p-1852.html

http://jhmotorsports.com/shop/catalog/images/JHM-B7-A4-20t-y-pipe-300.jpg

http://jhmotorsports.com/shop/catalog/exhaust-downpipe-jhm-to-25-for-b6-b7-s4-cat-back-on-b7-a4-20t-manual-cvt-p-1946.html

http://jhmotorsports.com/shop/catalog/images/JHM_B6-B7_S4_CatBack_By_FI.jpg

http://jhmotorsports.com/shop/catalog/exhaust-cat-back-jhm-b6-s4-stainless-steel-25-pipe-by-fi-p-384.html

Turbo vehicles have all of the back pressure they need before the turbo. Everything after the turbo is nothing more than restriction. Open up your exhaust system for optimal performance!


http://youtu.be/VAf5ycU6Kto

[Jake@JHM]

Thanks for the orders everyone! [up]

[08 classic]

Well I received my Y-downpipe and HFC from JHM (nice pieces) found a mid section from an S4 performance exhaust and I'm running that to my APR exhaust. I'm hoping some drone will be eliminated / reduced while also liven up the exhaust note (wishfull thinking). I know its tricky and it might not work but will see, kind like looking for the perfect girl can't stop trying...lol

Keep you posted once installed...

Take care

[Jake@JHM]

Well I received my Y-downpipe and HFC from JHM (nice pieces) found a mid section from an S4 performance exhaust and I'm running that to my APR exhaust. I'm hoping some drone will be eliminated / reduced while also liven up the exhaust note (wishfull thinking). I know its tricky and it might not work but will see, kind like looking for the perfect girl can't stop trying...lol

Keep you posted once installed...

Take care

Awesome! So you found an APR S4 catback? Do you know which version it is? Thanks for the order!

[08 classic]

The S4 is just the mid pipe with resonator (can't tell name brand), the pipes are 2.25", but I'm connecting that to my APR 2.0T exhaust...
and... still not installed yet, hopefully in two weeks.

Thank you..

[Jake@JHM]

The S4 is just the mid pipe with resonator (can't tell name brand), the pipes are 2.25", but I'm connecting that to my APR 2.0T exhaust...
and... still not installed yet, hopefully in two weeks.

Thank you..

Thanks for the orders everyone! These are all in stock and ready to ship!

[Jake@JHM]

Thanks for the orders everyone!

[Jake@JHM]

JHM 2.0T exhaust sale!! Woot!!!

http://www.jhmotorsports.com/products/pictures/B7A4/JHM-B7-A4-20T-Catless-Test-Pipe.jpg

JHM 3" 2.0T Test Pipe (http://jhmotorsports.com/shop/catalog/exhaust-test-pipe-jhm-catless-test-pipe-for-b7-a4-20t-p-1852.html) - Only $219.95!

http://www.jhmotorsports.com/products/pictures/B7A4/JHM-B7-A4-20T-Cat-pipe.jpg

JHM 3" 2.0T HFC (http://jhmotorsports.com/shop/catalog/exhaust-cat-pipe-jhm-high-flow-cat-hfc-for-b7-a4-20t-p-1893.html) - Only $369.95!

http://jhmotorsports.com/shop/catalog/images/JHM-B7-A4-20t-y-pipe-300.jpg

JHM Downpipe - Y Adapter - Tiptronic (http://jhmotorsports.com/shop/catalog/exhaust-downpipe-jhm-275-to-25-for-b6-b7-s4-cat-back-on-b7-a4-20t-auto-tip-p-2190.html)& Manual/CVT (http://jhmotorsports.com/shop/catalog/exhaust-downpipe-jhm-to-25-for-b6-b7-s4-cat-back-on-b7-a4-20t-manual-cvt-p-1946.html) - Only $469.95!

http://jhmotorsports.com/shop/catalog/images/JHM_B7-S4-cat-back-by-FI-for-site.jpg

JHM/FI S4 Cat backs are on sale TOO!! Clicky! (http://jhmotorsports.com/shop/catalog/advanced_search_result.php?keywords=FI+Cat+back&x=0&y=0)

[Andrew149]

Aww man! That test pipe is a killer deal!

[Jake@JHM]

Aww man! That test pipe is a killer deal!

Buy it!

[Andrew149]

Buy it!
Lol! No way in hell I'm changing my test pipe again.

[Jake@JHM]

Lol! No way in hell I'm changing my test pipe again.

Its a piece of cake! specially since you already have the OEM cat removed.

[Andrew149]

Its a piece of cake! specially since you already have the OEM cat removed.
Lol don't tell anyone that were in California :P

[Jake@JHM]

Lol don't tell anyone that were in California :P

oh, oops! shh...

[Jake@JHM]

Thanks for the orders everyone!

[NolanB7]

Jake is there any type of funky smell from running the test pipe.. How long is that there sale going to be lasting? Those prices are so tempting!

[mec]

Yes test pipe smells.
Not sure when sale ends is what jake will tell you.

[NolanB7]

Yes test pipe smells.
Not sure when sale ends is what jake will tell you.

Sale that never ends! Smell not to over bearing..?

[mec]

Sale that never ends! Smell not to over bearing..?

Depends on your nose. I suggest find someone local to smell their exhaust

[jimrobbington]

Sale that never ends! Smell not to over bearing..?
Some people think so, some don't. I love the smell, and it's not constant. Just every now and then you get a little whiff.

[mec]

Some people think so, some don't. I love the smell, and it's not constant. Just every now and then you get a little whiff.

I hate it lol. but its totally worth the +5 hp

[jaycurn]

Mine definitely stinks a bit, but it's just a pleasant reminder for me, every time I start the car, how much I hate hippies! [o_o]

[Jake@JHM]

JHM/FI Used Cat back for sale: http://www.audizine.com/forum/showthread.php/622967-Fast-Intentions-S4-B6-Full-Exhaust

[toomeyct]

JHM/FI Used Cat back for sale: http://www.audizine.com/forum/showthread.php/622967-Fast-Intentions-S4-B6-Full-Exhaust

Man, you even help sell other people's stuff. Bravo.

[hail]

[Jake@JHM]

Man, you even help sell other people's stuff. Bravo.

[hail]

I try to help everyone! [up]

[jaycurn]

JHM/FI Used Cat back for sale: http://www.audizine.com/forum/showthread.php/622967-Fast-Intentions-S4-B6-Full-Exhaust

I'd be all over this if it was the quad tip B7 version! [headbang]

[toomeyct]

Anybody have any experience with the HFC and Downpipe and Colorado emissions? Just switch in the factory exhaust every 2 years or does it pass?

[Jake@JHM]

Anybody have any experience with the HFC and Downpipe and Colorado emissions? Just switch in the factory exhaust every 2 years or does it pass?

I don't know your states regulations, but we have never had an issue with a customer passing out the pipe with our HFC, and that includes our A4, S4, RS4, and S5 customers.

[Jake@JHM]

Another http://forums.fourtitude.com/showthread.php?7072216-Fast-Intentions-Catback

[Jake@JHM]

More orders out the door! Thanks guys!

[PNW Avant]

Once I finish my carbon cleaning and change that timing belt I'm going to finally treat myself to a HFC...just you wait!!!!! [:D]

[Jake@JHM]

Once I finish my carbon cleaning and change that timing belt I'm going to finally treat myself to a HFC...just you wait!!!!! [:D]

OOhhhh you lucky duck!!!

[Jake@JHM]

Some body swoop this!!

http://www.audizine.com/forum/showthread.php/627841-B7-S4-Fast-Intentions-Cat-Back?p=10320199#post10320199

[mcbuck]

FedEx delivered my test pipe last night. Felt like a kiddy on christmas morning...

First impression was "oooooh, pretty....." Nice fit and finish and the JHM logo is a cool touch.

Hope to get some time this weekend to install it and see what difference it makes over the stock cat w 230K on it.

[Jake@JHM]

FedEx delivered my test pipe last night. Felt like a kiddy on christmas morning...

First impression was "oooooh, pretty....." Nice fit and finish and the JHM logo is a cool touch.

Hope to get some time this weekend to install it and see what difference it makes over the stock cat w 230K on it.

Right on!! Yo should notice a nice gain in performance. You should also look into our software for an even bigger gain! ;)

[Jake@JHM]

Thank you for the orders everyone!!

http://tapatalk.imageshack.com/v2/15/02/13/eeb167dd95df62e73c8475cacdc59fd6.jpg

[mec]

Thank you for the orders everyone!!

http://tapatalk.imageshack.com/v2/15/02/13/eeb167dd95df62e73c8475cacdc59fd6.jpg

That looks like an expensive add on that could be cut out to save 10-15 bucks a test pipe lol


Sent from my iPhone using Tapatalk

[Jake@JHM]

That looks like an expensive add on that could be cut out to save 10-15 bucks a test pipe lol


Sent from my iPhone using Tapatalk

We added them for FREE!

[mec]

We added them for FREE!

Well that doesn't make sense.

You can't add anything for free unless it's air. But then you are paying for shipping that air so it isn't free.

If the price is $300, cut that off, save $30!

Water jet cut I would assume?


Sent from my iPhone using Tapatalk

[Jake@JHM]

Well that doesn't make sense.

You can't add anything for free unless it's air. But then you are paying for shipping that air so it isn't free.

If the price is $300, cut that off, save $30!

Water jet cut I would assume?


Sent from my iPhone using Tapatalk

Laser cut [up].

[mec]

Laser cut [up].

Laser cut! damn not even plasma, you guys are on that new new.

[Jake@JHM]

Laser cut! damn not even plasma, you guys are on that new new.

Of course!!

[mec]

Of course!!

what kinda lazer.........

You guys want to cut out some flanges for me :) depending on what you have you might have enough power, otherwise I'll need to find a plasma

[Jake@JHM]

what kinda lazer.........

You guys want to cut out some flanges for me :) depending on what you have you might have enough power, otherwise I'll need to find a plasma

Lol it would be cheaper if you DIY'd it.. unless you bought like 10+ sets of whatever it is.

We use sharks with Laser Beams attached to their for heads. Do you know how much labor intensive that is?

[mec]

Lol it would be cheaper if you DIY'd it.. unless you bought like 10+ sets of whatever it is.

We use sharks with Laser Beams attached to their for heads. Do you know how much labor intensive that is?

Shouldn't be very labor intensive unless your sharks aren't laser certified in which case they shouldn't be cutting anything!

You guys outsource it then? I've got a cad file that I need laser cut out of steel or aluminum.

[Jake@JHM]

Shouldn't be very labor intensive unless your sharks aren't laser certified in which case they shouldn't be cutting anything!

You guys outsource it then? I've got a cad file that I need laser cut out of steel or aluminum.

Not out sourced, we do it at our machine shop where we machine our shifters, b8 flywheels etc..

[drumnjuny]

Not out sourced, we do it at our machine shop where we machine our shifters, b8 flywheels etc..

you guys have your own machine shop?

[Andrew149]

you guys have your own machine shop?

034 make's there shifter knob's and flywheels

[Jake@JHM]

Negative. They make our B5-B7 flywheels. We make their knobs and shifters.

[NolanB7]

Jake, Has anyone that you have heard of come across any fitment issues with CTS's HFC and your guys JHM Y down pipe? I know it says, it bolts up to other aftermarket pipes. Just don't wanna order and have fitment issues, and etc..?

[Jake@JHM]

If their HFC was designed to fit in 100% stock location you should be good!

[aluthman]

Laser cut! damn not even plasma, you guys are on that new new.

Just like the K03 flange I bought from them [up]

[brandonpham]

Ah I want a HFC or test pipe from the feedback, but after my maintenance items I wanted JHM Stage 1! I neeeeeeeeed it.

I feel like a HFC or test pipe won't be as impressive for me unless i go tuned first.

[aluthman]

Buy them at the same time!

[brandonpham]

I felt my wallet cringe in my back pocket as I read that. Lol.

Maybe I should as a late birthday gift from a week ago. [:D]

[drumnjuny]

dew it!

[billyhoyle]

Ah I want a HFC or test pipe from the feedback, but after my maintenance items I wanted JHM Stage 1! I neeeeeeeeed it.

I feel like a HFC or test pipe won't be as impressive for me unless i go tuned first.

True, but the tune will be sooooo much better with a HFC or test pipe. They are one of the best 'bang for you buck' hardware upgrades you can do for this car.

[brandonpham]

But won't I appreciate the HFC/Test Pipe MORE if I get tuned, wait a bit, then remove my cat. [rolleyes]

[billyhoyle]

Haha yeah, you might. You'll get two smaller bumps in performance spaced out rather than all at once. Depends which type of junkie you are I guess!

[brandonpham]

Haha yeah, you might. You'll get two smaller bumps in performance spaced out rather than all at once. Depends which type of junkie you are I guess!

I mean the 2.0t is gonna have engine limits, might as well split up the enjoyment to last as long as I can haha.

From driving 2JZ s13 240s and built SR20s to superfast 335s and a plethora of FCs and Subarus amongst my friends, I've always been the more conservative car in the group lol.

[Jake@JHM]

I mean the 2.0t is gonna have engine limits, might as well split up the enjoyment to last as long as I can haha.

From driving 2JZ s13 240s and built SR20s to superfast 335s and a plethora of FCs and Subarus amongst my friends, I've always been the more conservative car in the group lol.

Looks like you are going to need our stage 3 kit when it is ready.. [evilsmile]

[Jake@JHM]

Just like the K03 flange I bought from them [up]

Pretty sweet right?

[aluthman]

Pretty sweet right?

Yup, I almost want to polish it and hang it on the wall. How much longer until the atage 3 is available to someone who doesn't need the software to go with it?

[Jake@JHM]

Yup, I almost want to polish it and hang it on the wall. How much longer until the atage 3 is available to someone who doesn't need the software to go with it?

We got more if you want to use on for decor! Not sure yet, we are still in the process of streamlining the parts for production. Hopefully something this spring!

[brandonpham]

Looks like you are going to need our stage 3 kit when it is ready.. [evilsmile]

Are you saying I can keep up with 13b turbo 2s, sr20s, tuned ej257s, and 4g63s..with the little 2.0t that could!?[drool]

[Jake@JHM]

Are you saying I can keep up with 13b turbo 2s, sr20s, tuned ej257s, and 4g63s..with the little 2.0t that could!?[drool]

My car ran 12s with stock internals and trapped 106mph, and we are still refining the software. That is tuned RS4 territory.

[brandonpham]

My buddy's 335i on JB4, RB4 turbos, ams FMIC, meth, etc. ran 13.1 on slicks with a boost leak, but even that car pinned you. This was back when I had my unflashed Acura TSX.

If I could touch that territory, we are talking business Jake.

So.. is Stage 2 still a free upgrade if I get Stage 1? Sorry, I haven't been following recently. Not sure when the promo ends so I know when to buy my tune!

[Jake@JHM]

My buddy's 335i on JB4, RB4 turbos, ams FMIC, meth, etc. ran 13.1 on slicks with a boost leak, but even that car pinned you. This was back when I had my unflashed Acura TSX.

If I could touch that territory, we are talking business Jake.

So.. is Stage 2 still a free upgrade if I get Stage 1? Sorry, I haven't been following recently. Not sure when the promo ends so I know when to buy my tune!

It sure it!
Looks like our stage 3 kit is right up your alley [up]

[brandonpham]

How long do you expect the promo to last?

By the way did you ever get that lost cam follower sent back to you guys?

They shipped it to 22 instead of my house at 222. I went over to the house at 22 and they said they never received anything.

[Jake@JHM]

How long do you expect the promo to last?

By the way did you ever get that lost cam follower sent back to you guys?

They shipped it to 22 instead of my house at 222. I went over to the house at 22 and they said they never received anything.

No idea, once the higher-ups tell me it has ended [:/]

Nope! That follower is lost in the wind somewhere [=(]

[FoRbAnNa]

Jake,
Will the JHM HFC/test pipe mate up to the upcoming stage 3 kit or would that require another HFC/test pipe? On a side note, is it possible to get the JHM HFC without the JHM logo on it? I know it's amazing but.. Because of inspections.. [;)]

[Jake@JHM]

Jake,
Will the JHM HFC/test pipe mate up to the upcoming stage 3 kit or would that require another HFC/test pipe? On a side note, is it possible to get the JHM HFC without the JHM logo on it? I know it's amazing but.. Because of inspections.. [;)]


It absolutely will bolt right up to our stage 3 kit!

We can do that for you if you leave a note in your order comments. It just may take an extra day or so before it will ship because the ones we have fabricated already already have the logo on it.

Jake

[Jake@JHM]

Thanks for the orders guys!

[Roaldtm]

Just to clarify Jake, the test pipe will not trigger any CEL neither, regardless of stock or tuned because the J-Bung right?

[Jake@JHM]

Just to clarify Jake, the test pipe will not trigger any CEL neither, regardless of stock or tuned because the J-Bung right?

We specifically made the calculations for the J-Bung to NOT trigger a CEL on both the TP and HFC [up]. Even on the stock software!

[jimrobbington]

Jake,
Will the JHM HFC/test pipe mate up to the upcoming stage 3 kit or would that require another HFC/test pipe? On a side note, is it possible to get the JHM HFC without the JHM logo on it? I know it's amazing but.. Because of inspections.. [;)]


It absolutely will bolt right up to our stage 3 kit!

We can do that for you if you leave a note in your order comments. It just may take an extra day or so before it will ship because the ones we have fabricated already already have the logo on it.

Jake
Can you also rust it up and make it look old? For reals though, if I were to do a cut-out for some reason, and it were to happen on your 3" test pipe, would said 3" test pipe be able to mate directly up to my 2.5" Techtonics downpipe AND would you be able to fabricate also said 3" JHM test pipe cut-out conversion for me so all I have to do is install it.

[Jake@JHM]

Can you also rust it up and make it look old? For reals though, if I were to do a cut-out for some reason, and it were to happen on your 3" test pipe, would said 3" test pipe be able to mate directly up to my 2.5" Techtonics downpipe AND would you be able to fabricate also said 3" JHM test pipe cut-out conversion for me so all I have to do is install it.

Absolutely! Send us your car and it will be returned to you ball'n!

[jimrobbington]

Absolutely! Send us your car and it will be returned to you ball'n!
:(

[Jake@JHM]

:(

It would be too hard to something custom without the car here, otherwise there is the possibility of it fitting like poop.

[Jake@JHM]

More JHM Exhaust Components out the door! Thanks for the orders everyone!

[Jake@JHM]

Thanks for the orders everyone!

[Shanster]

suck up

[Jake@JHM]

suck up

Shh!

[Jake@JHM]

Free B7 S4 Catback!!!

http://sfbay.craigslist.org/nby/pts/5116139895.html

Go scoop that up YO

[brandonpham]

free b7 s4 catback!!!

http://sfbay.craigslist.org/nby/pts/5116139895.html

go scoop that up yo

damnit why not nj

[gonemtbiking]

Free B7 S4 Catback!!!

http://sfbay.craigslist.org/nby/pts/5116139895.html

Go scoop that up YO

http://images.tapatalk-cdn.com/15/07/11/bed5594a131d71a6815baed1df041a43.jpg


Sent from my iPhone using Tapatalk

[MISKIE]

http://images.tapatalk-cdn.com/15/07/11/bed5594a131d71a6815baed1df041a43.jpg


Sent from my iPhone using Tapatalk

Good job!!!


Sent from my iPhone using Tapatalk

[CLEANA3]

That's one way to do it. Also you will love the set up with the S4 exhaust, have had mine for about a year now and its perfect.

[DanKing]

Any one if the test pipe or HFC will pass the new smog test as of this year in cali.

They have changed the test if you have a car newer than the year 2000. All they do if plug something in2 your OBDII slot. Not rolling road or shit inside your exhaust .... :-)

[gonemtbiking]

Any one if the test pipe or HFC will pass the new smog test as of this year in cali.

They have changed the test if you have a car newer than the year 2000. All they do if plug something in2 your OBDII slot. Not rolling road or shit inside your exhaust .... :-)

As far as I know they do both the ODB-II check as well as a visual. I remember some of the B5/6 guys would weld the stock cat heat shield over the HFC or test pipe to pass the visual. So it should all come down to how close the inspector will look. According to Jake, with the J tubes, both the test pipe and HFC will not throw a code.


Sent from my iPhone using Tapatalk

[MISKIE]

Can't wait to get mine! Thanks all [emoji41]


Sent from my iPhone using Tapatalk

[Jake@JHM]

http://images.tapatalk-cdn.com/15/07/11/bed5594a131d71a6815baed1df041a43.jpg


Sent from my iPhone using Tapatalk

Like a boss!


Any one if the test pipe or HFC will pass the new smog test as of this year in cali.

They have changed the test if you have a car newer than the year 2000. All they do if plug something in2 your OBDII slot. Not rolling road or shit inside your exhaust .... :-)

All of these exhaust products are for "off road use only". However, like previously mentioned you won't throw a code due to the design of the J-bung. We have had customers in the past go get smogged though with our full system.

[Jake@JHM]

http://sfbay.craigslist.org/sby/pts/5120004454.html

Another cat back! Sadly, not free this time.

[MISKIE]

Thanks for the orders everyone!

Just ordered both TP & DP-Y!!!


Sent from my iPhone using Tapatalk

[Jake@JHM]

Another OEM cat back available!

http://www.audizine.com/forum/showthread.php/666069-OEM-B7-S4-Exhaust

[Jake@JHM]

FREE B7 OEM S4 CatBack!!!

http://www.audizine.com/forum/showthread.php/642536-Stock-B7-S4-Exhaust?p=11037828#post11037828

[Jake@JHM]

Thanks for all of the orders everyone!

[TheTrith]

Do those quad S4 tips fit the stock B7 A4 rear valence, or do you have to modify it to a single tip on each side?

[MISKIE]

Do those quad S4 tips fit the stock B7 A4 rear valence, or do you have to modify it to a single tip on each side?

You need to modify your stock valance if you're getting a quad tip. Or buy a quad tip rear valance.

I opted for a B6 S4 CB, no modification required.


Sent from my iPhone using Tapatalk

[Jake@JHM]

We have the S4 rear valance available for those wanting to go with quad tips!

[james12lucy]

As far as I know they do both the ODB-II check as well as a visual. I remember some of the B5/6 guys would weld the stock cat heat shield over the HFC or test pipe to pass the visual. So it should all come down to how close the inspector will look. According to Jake, with the J tubes, both the test pipe and HFC will not throw a code.


Sent from my iPhone using Tapatalk

We have the same set-up in Ontario, Canada. Mine passed without a second thought; I was in and out of the emissions test in under 15 minutes, and $37.65 CAD. They don't a visual here; if they did, I'd build a removable heat shield that clamped on for the tests...

[TheTrith]

You need to modify your stock valance if you're getting a quad tip. Or buy a quad tip rear valance.

I opted for a B6 S4 CB, no modification required.


Sent from my iPhone using Tapatalk

Ah gotcha, thanks! Looks like I'll be looking for the B6 S4 exhaust

[Jake@JHM]

Thanks for all of the orders everyone!!

The shelves are freshly stocked with Test Pipes, HFCs, and Downpipes!!!

[mlavelle92]

Damn, 400 dollars seems steep after seeing these. But I supposed I didn't have to haul one you guys

[Jake@JHM]

Damn, 400 dollars seems steep after seeing these. But I supposed I didn't have to haul one you guys

And we have to take up spacing storing stock systems.

[mlavelle92]

And we have to take up spacing storing stock systems.

Like the other cat backs leaned up against the outside of the rear garage next to the tarped rs4 ;) just teasing I like you guys and don't mind giving you money. [up][drive], Its why everyone on my car is JHM/034. Gotta keep it local!

[h0yitsdom]

Do you guys have any specials coming up or like military discount?
Looking at ordering a 2.0T testpipe

[Jake@JHM]

Do you guys have any specials coming up or like military discount?
Looking at ordering a 2.0T testpipe

Holiday sale is coming up, but it is already on sale so not sure if it will change or not!

[h0yitsdom]

http://theimpactnews.com/wp-content/uploads/2013/02/ShutUpAndTakeMyMoney.jpg

[Jake@JHM]

http://theimpactnews.com/wp-content/uploads/2013/02/ShutUpAndTakeMyMoney.jpg

Let me know if you need help placing an order!

[h0yitsdom]

Order 41560 successfully placed

[Jake@JHM]

Order 41560 successfully placed

What size shirt!? [up]

[h0yitsdom]

What size shirt!? [up]

Medium [drool]

[Jake@JHM]

Medium [drool]

You got it bud [up]

[Jake@JHM]

Thanks for the orders everyone!

[j.gerbes]

Hey Jake... Your Audizine mailbox is full. Could you clear it so I can send a PM? :)

[Jake@JHM]

Hey Jake... Your Audizine mailbox is full. Could you clear it so I can send a PM? :)

Cleared, thanks!

[shahk62]

Cleared, thanks!

Hey Jake. Big fan of your build and the r&d put into the platform. I'm just wondering are you guys doing any work on the transmissions for tip cars? I would really like to go stage 2+ or big turbo but naturally the tranny is the limiting factor. Cheers

[Jake@JHM]

Hey Jake. Big fan of your build and the r&d put into the platform. I'm just wondering are you guys doing any work on the transmissions for tip cars? I would really like to go stage 2+ or big turbo but naturally the tranny is the limiting factor. Cheers

Thanks!!

The Tip transmissions are better than most people think. They are practically the same transmission as the S4 and we have tons of Tip guys with our supercharger kit. You will be more than fine as long as you keep up on the maintenance.

It has been a long project, but we do have TCU tuning in the works as well!

[adam044]

Added the high flow cat to my parts to buy later list. I'll add it when I go from customs cat back to custom turbo back and have the shop make the downpipe while adding the JHM cat.

[Jake@JHM]

Added the high flow cat to my parts to buy later list. I'll add it when I go from customs cat back to custom turbo back and have the shop make the downpipe while adding the JHM cat.

Right on! Going 3"?

[adam044]

Right on! Going 3"?

The cat back I got is 2.5", so I'll go 3 down to 2.5. I'll do the turbo back probably once I get tuned.

[Jake@JHM]

Oh nice!

[adam044]

Oh nice!

Not going crazy on performance, full custom turbo back w/JHM cat basic stage 1 tune is good for me. Now if I had a second car it'd be different. :)

[Jake@JHM]

That amount of performance is more than enough for most people surprisingly!

[adam044]

That amount of performance is more than enough for most people surprisingly!

I believe it!

[shahk62]

Thanks!!

The Tip transmissions are better than most people think. They are practically the same transmission as the S4 and we have tons of Tip guys with our supercharger kit. You will be more than fine as long as you keep up on the maintenance.

It has been a long project, but we do have TCU tuning in the works as well!


Are both transmissions a 6HP19A? or does the S4 have a different code.

[Jake@JHM]

Thanks for the orders everyone!

[NolanB7]

Jake, quick question. I have full exhaust setup, 3" catless tp- jhm Y dp- b6s4 exhaust. On the dp, right before it Y's out . I am getting chatter from if being up against what I think is trans/differential mount, from it resonating. Just wondered if anyone came to you with this issue an if you have tips or fixes. Other than chatter, I love this exhaust.
Included link to pic with mount I am trying to explain..https://www.google.com/search?biw=360&bih=289&ei=K1MVWInCG4jImQHqtKfgAw&q=b7+a4+downpipe+on+car&oq=b7+a4+downpipe+on+car&gs_l=mobile-gws-serp.3..33i160k1l2.4765.7374.0.8203.7.7.0.0.0.0.19 2.865.1j6.7.0....0...1.1.64.mobile-gws-serp..0.4.512...0j0i22i30k1.TOV0VZzCYnQ#imgrc=pxz3 dA38XvoCbM%3A

[DeathBlow]

I got my JHM Shirt!!!

[yxri]

I got my JHM Shirt!!!

Post a selfie

[DeathBlow]

Post a selfie
you got it!

[Tech/Sales@JHM]

Thanks for the orders everybody!

[DeathBlow]

Post a selfie

http://i25.photobucket.com/albums/c68/deathb5433/IMG_5100.jpg (http://s25.photobucket.com/user/deathb5433/media/IMG_5100.jpg.html)

[Jake@JHM]

http://i25.photobucket.com/albums/c68/deathb5433/IMG_5100.jpg (http://s25.photobucket.com/user/deathb5433/media/IMG_5100.jpg.html)

OHH SSNNAAPPPP


Model over here [>_<]

[DeathBlow]

LOL.. Let me know if you need one. once the weather gets a little better need to call you guys about the K04-R. Again thanks for all the help with the car!!!

[Jake@JHM]

Thanks for the orders everyone!

[Jake@JHM]

Thanks for the orders everyone!

[BenMTL]

Jake, can you please reply to this thread?

Multi JHM tune users have the exact same problem;

http://www.audizine.com/forum/showthread.php/781316-B7-A4-Hesitation-Jerky-Acceleration-Fuel-Problem

[Tech/Sales@JHM]

Thanks for all of the orders! Let us know if you have any questions [up]