OEM Votex Skirts: the DIY

[fly300kts]

Hi,

Because some of you have purchased the OEM Side Skirts, you will find attached a DIY

Tools = Generic
Difficulty = 3
Time = 1.5 hrs per side
Manpower = 2 souls for final install

First, remove the door blades from the front and rear door. There are 2 screws holding them in place, front and aft of each door.
AFT
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P01.jpg

Front
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P02.jpg

Using a flat screwdriver and starting by one end, lift and pull towards the outside of the car, the doorstep rubber trim
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P03.jpg

Remove the 2 screws on the front wheel well
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P04.jpg

Remove the 2 screws on the rear wheel well. Remove also the trim under the chassis; you will need to modify it later. Remove it completely!
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P05.jpg

Now remove the wagon of screws on top and bottom of the existing skirt.
Don’t forget this one hiding behind the front door
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P06.jpg

Bottom
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P07.jpg

Skirt removed
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P08.jpg

Clean really well the areas covered by the old skirt, I used MEK.

My kit was manufactured in 2006 and I was not happy by the stickiness of the tape already installed. I decided to remove it, and after a little trip to home Depot, I bought a brand new roll of 3M tape, double sided and really sticky.

Old tape
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P09.jpg
Once the old one is removed, clean the area with MEK. CAREFUL NOT TO TOUCH THE FRESH PAINT!!!!
Install the new tape and respect the cut off areas.
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P10.jpg

On the rear corners, my set had masking tape on them. Peel it off, clean with MEK and install a piece of tape on each cut off areas of the skirts

Cut off areas
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P11.jpg
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P12.jpg

Now with the tape installed
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P13.jpg

Equip and install the 3 brackets
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P14.jpg

Equip the new rear bracket provided with the 3 rapid nuts and install on the car.
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P15.jpg

Installed
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P16.jpg

This is when you need to call your Friend: Peel off the protective side of the tape on the entire skirt. Starting from the back, present the skirt and install the upper screw on the rear bracket while your Friend is holding the front part of the skirt away from the chassis

Top screw installed
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P17.jpg

Go to the front and clip the skirt to the chassis. With a clean rag, press firmly on the entire length of the doorstep and the result should look like this
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P18.jpg

With a razor blade, cut the rear trim as follow because it will not longer fit inside the new skirt
Cut off
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P19.jpg

Installed
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P20.jpg

For the front wheel well, you will note that now, the skirt goes on top of the plastic well while it was under before. This is why you need to use now the long screws provided.

Reuse also the same screws to secure the 3 brackets under the chassis to the car.

One side done, one to go.
http://i31.photobucket.com/albums/c395/fly300kts/Votex%20Skirts/P21.jpg

Pictures of the car will come later...after a good bath [:D]
Let me know if any question

Phil

[cheemn]

Very nice! Cant wait to see finished install. You are a Jedi in the World of Audizine. LOLOL :-) Would be cool if ya had comparison pics of before and after of a side view of the car. I still cant tell from all the pics I have seen all over the web just how much lower thse things go than the original side skirts. If they look good I might buy a pair and keep them till I want to put them on later. My local Audi dealer still has a set. :-)

[Doctor]

Once more really helpful Phil. Thanks again for the input.
Are you running S4 Door blades, or S-line ones...?

I am thinking of going with S4 ones so just asking, thanks.

[fly300kts]

Here is an old picture of my car.
The skirts are about 1/2 inch lower than original, but still above any components under chassis
http://i31.photobucket.com/albums/c395/fly300kts/IMG_6648Large-1.jpg

Phil

[fly300kts]

Once more really helpful Phil. Thanks again for the input.
Are you running S4 Door blades, or S-line ones...?

Always a pleasure my Friend
These are S-Line blades

phil

[cheemn]

wow thanks again phil. you are fast!!! :-)

[4ty-phive]

I have a question. Did you paint yourself, or did you pay someone? Either way, what did you pay (if you don't mind)? Great post.

[gpxluke]

nice mod~~~

where did u buy your side skirt? and how much did u pay for it

[fly300kts]

I have a question. Did you paint yourself, or did you pay someone? Either way, what did you pay (if you don't mind)? Great post.

I do prep and paint myself. I just borrow the paint both where I work. Base + clear cost me for a pint: $140. But I have a lot left for the rear DTM bumper once I get it
Phil

[fly300kts]

nice mod~~~

where did u buy your side skirt? and how much did u pay for it

Got them from the Dealer and paid $79.20
http://i31.photobucket.com/albums/c395/fly300kts/IMG_5591Large.jpg

phil

[gpxluke]

.....holy crap that's fucking cheap~~~~

I am gonna drop by my dealer and check out the price...why it's so cheap -_-?

[fly300kts]

.....holy crap that's fucking cheap~~~~

I am gonna drop by my dealer and check out the price...why it's so cheap -_-?

Yes, it's really cheap and this price include the 2 skirts primed, all the hardware, the 6 side brackets and the 2 rear ones.
Not sure why they dumped the price but for your information, I have been really lucky that my Dealer had a set in stock so if I were you, I would hurry up because this Discount, is well known in the Cummunity
Phil

[gpxluke]

haha sure i'll definitely go check them out tomorrow

[europaisch]

Great write up. Thank you! I can't wait to install my set. I have a lot more confidence after reading this write up!

[psiaddict85]

I'll be doing mine soon too... That will complete my full DTM Kit!

[Geoffafa]

dude 80 dollars only? wow thats awesome!! Phil you should swing by tomorrow night

[Tusin]

Great DIY! Thank you Phil!

BUT hmmmm. This was my concern with these. I think anything other than the non-sline door blades look a little funky. Which kind of makes sense as the votex kit was molded for a non-sline car. Phil do you still have your stock blades? If so maybe slap a side on to compare?

[SEXICÄN]

nice DIY, but i don't see a huge difference....

[psiaddict85]

nice DIY, but i don't see a huge difference....

Ohh but it is :)

[fly300kts]

dude 80 dollars only? wow thats awesome!! Phil you should swing by tomorrow night

Hey Boss, won't be able to. I am flying tomorrow night. I will call you next time I come, to make sure you are there (you know what I mean)

Phil

[fly300kts]

Great DIY! Thank you Phil!

BUT hmmmm. This was my concern with these. I think anything other than the non-sline door blades look a little funky. Which kind of makes sense as the votex kit was molded for a non-sline car. Phil do you still have your stock blades? If so maybe slap a side on to compare?

I won't be able to compare because I don't longer have my OEM blades. sorry

Phil

[fly300kts]

nice DIY, but i don't see a huge difference....

There is Sexican, believe me. To give you an idea, on the rear door, the edge of the door blade is flush with the skirt

Phil

[audimeister]

nice DIY, but i don't see a huge difference....

S line door blades are hiding the skirts. With stock blades, the effect is very RS4-like, especially in person.

If you look at a side shot of an S line or S4, the lower definition of the body (and front valence lip) is at the bottom of the doors. With DTM, Votex, and RS4, the line is shifted to below the doors, making the car appear lower and more aggressive.

Mixing the two (door blades plus skirts) just looks confused, IMHO. But hey, whatever makes people happy, I guess.

Nice DIY- way better than the included instructions...

[Geoffafa]

Hey Boss, won't be able to. I am flying tomorrow night. I will call you next time I come, to make sure you are there (you know what I mean)

Phil

No problem Phil, just give me a call. We are either at Moe's or at the shop, either way you're always welcome :) Have a safe trip!

[FASTONE]

Nicely done Phil.

[CleverA4Name]

Phil thanks for this write up! My order is supposed to come in today/tomorrow and I am getting them painted as part of an accident where someone hit me on my drivers door! I am wondering though if I should put them on now or wait for my DTM front/rear. Any ideas?

[fly300kts]

Your welcome.
I will put the skirts on now.
I found a rear DTM bumper as well. Should be here in 4 days

Phil

[SEXICÄN]

Your welcome.
I will put the skirts on now.
I found a rear DTM bumper as well. Should be here in 4 days

Phil

Sorry i couldn't get it for you sooner

I'm sure it looks good in person, but i dunno....

How much are they?

[audimeister]

http://www.audizine.com/forum/showthread.php?181683-POST-your-Quartz-Gray-Metallic-colour-A4-here-!!/page2&highlight=gray+dtm+skirts

About halfway down the page, there's a lot of pics of a quartz gray car featuring Votex skirts. Probably gives a better idea of the effect.

[SEXICÄN]

So almost looks like the VOtex and side that come on the DTM. Are they the same?

[fly300kts]

Yes they are

Phil

[barro]

Looks amazing!! Again;)

Do you have any OEM numbers for that skirt kit?

Looks very clean with S4 door blades as well.

[audimeister]

Yes they are

Phil

Actually, no. Different part numbers, and it appears that Votex stick out slightly farther.

[Tusin]

Yup exactly the same.... Hmmm I have a decision to make. I have S4 door blades, and still have the stock OEM blades. My Votex skirts are not in yet. But I think either not use the votex skirts, and keep with the S4 blades. Or sell the S4 blades and put the OEM ones on with the votex skirts.

[fly300kts]

Or you compromise and get Sline blades with skirts. I think the S4 blades will be too aggressive and will way out the skirts

Phil

[SEXICÄN]

I have the CF S4 door blades and would consider doing this, but i would need a picture of these and S4 door blades on...

[fly300kts]

Looks amazing!! Again;) Do you have any OEM numbers for that skirt kit?

Voila: 8EC-071-685-9AX

Phil

[barro]

And these Votex fits with S-line or S4 door blades?

Even more interesting;)

[fly300kts]

And these Votex fits with S-line or S4 door blades?

Even more interesting;)

Yes they do

Phil

[ECS Tuning-Audi]

These are designed for A4 Sedans and A4 Avants as well as S4 Sedans and S4 Avants. We are running a sale on a couple of Votex items:
http://www.audizine.com/forum/showthread.php?349315-ECS-Tuning-B7-Votex-Side-Skirts-and-Avant-Spoiler-85-OFF

[Tusin]

Just picked mine up. Paid "retail" but $99.99 for a set, with no extra shipping and considering I live in Alaska.... Good stuff!

[fly300kts]

I am glad that you were able to find a set. Good Job !

Phil

[Tusin]

Phil. I briefly look at mine. And something that struck me. I use a low profile floor jack, with a hockey puck on it and jack up from the pinch weld. Are the skirts going to cause any problems or get in the way at all?

[fly300kts]

no, I don't think so. You have a cut out for the jack point areas

Phil

[Sharkfin]

I got mine ordered as well but won't be painting until I have the DTM rear. Do you get that from the dealer too Phil?

And Sexican, actually it looks much more aggressive to me with a wider body look below the door. I even like the S4 blades with them as well.

And for all who were debating these are Votex and they are the DTM side skirts as well, same parts. I also need these to complete my DTM conversion.

[Tusin]

Yeah just not feeling these with the blades. But to each their own right? Think I may have to sell the blades, more money for other mods!

[Sharkfin]

Do you have S4 ones?

BTW I just checked VWs site and there are only 80 sets of side skirts in the country remaining.

[fly300kts]

I got mine ordered as well but won't be painting until I have the DTM rear. Do you get that from the dealer too Phil?

And Sexican, actually it looks much more aggressive to me with a wider body look below the door. I even like the S4 blades with them as well.

And for all who were debating these are Votex and they are the DTM side skirts as well, same parts. I also need these to complete my DTM conversion.

Yes, got the rear bumper from my Dealer, actually, I have to wait few days but got a nice discount. Once in my hand, I will first fill the reflectors, then paint. Ordered the 2 brackets from Genuine.
Everything should be done and installed in a week or so.

Phil

[ECS Tuning-Audi]

As per the jacking issue, if you click the picture you can blow it up, but the holes are cut out for a jack at the pinch weld. I don't see any issue with being able to jack the car up by them?
http://intra-img.ecstuning.com/product_library/71458/300/Side%20Skirt%20Set.jpg (http://www.ecstuning.com/Audi-B7_A4-Quattro-2.0T/Exterior/Body/Votex_Parts/ES4544/?salesrep=CArmbruster&utm_source=audizine&utm_medium=forum&utm_content=CArmbruster&utm_campaign=postreply)

[Tusin]

Yeah I agree. I took a look at mine in person and the hole cut out are pretty good sized. Being "OEM" I am sure they kept that in mind, to at least allow for lift use.

[SEXICÄN]

Just ordered them from my parts depo! lest expensive side skirts i have ever bought!

[Sharkfin]

Phil, how much did you pay for the rear? And is there a reason you didn't get the one without reflectors?

[fly300kts]

I paid $355 for the rear. As previously said, I ordered the inserts from Genuine for $75.
I ordered the dual exhaust to keep my oval tips. As far as the reflector, I don't think you will find a bumper who don't have them since it's a DOT required. I forgot, I ordered without parking sensors

Phil

[Sharkfin]

Actually, ecs sells them without the reflector: http://www.ecstuning.com/Audi-B7_A4-Quattro-2.0T/Exterior/Body/DTM_Package/ES1263330/

PM sent

[fly300kts]

Yes, but single tip

Phil

[beantown]

Just ordered them from my parts depo! lest expensive side skirts i have ever bought!

Going to call my dealer today! Hey man, which do you think the cost would be to have these painted?

[SEXICÄN]

Can't be more than $100

I'm with you Nate, I had to get them to complete the DTM look!

[Tusin]

You really think you can get them sprayed for a bill? I have a feeling up here in Anchorage it is going to be 200+.....

[beantown]

You really think you can get them sprayed for a bill?..

I guessing that's just a quick estimate, seeing that Sexican probably can get one of his guys to paint it for like $20!

[Tusin]

hahah true that.

[SEXICÄN]

i got my front end sprayed for $150 and these are smaller... I'd guess $100. Well thats what i was quoted...

[Sharkfin]

$150 for the bumper only is cheap

[fly300kts]

Cost me nada, beside the materials, I do it myself

Phil

[Tusin]

Dude more pics! :)

[fly300kts]

I will as soon as I receive the last piece of the puzzle

phil

[Tusin]

What the DTM rear? Bleh. MORE PICS! :)

[Tusin]

Hey man quick question. Just had mine painted so the install will be within the next few weeks (snowed yesterday). The instructions state to use a glue where that masking tape was. Have you had any issues at all with just using the double sided tape?

[volcomic]

Hey man quick question. Just had mine painted so the install will be within the next few weeks (snowed yesterday). The instructions state to use a glue where that masking tape was. Have you had any issues at all with just using the double sided tape?

You don't need glue. They're screwed in on both ends, screwed in from the bottom, clipped in to the car with "tabs" in the front, and then taped along the top on your sills. Unless you got a really old set with crappy tape, they'll be fine [up] Just make sure everything is super clean before you stick them down.

[fly300kts]

Hey man quick question. Just had mine painted so the install will be within the next few weeks (snowed yesterday). The instructions state to use a glue where that masking tape was. Have you had any issues at all with just using the double sided tape?

As explained in my DIY, I replaced the existing tape with new 3M tape, no glue

Phil

[CleverA4Name]

Hey Phil, when you did this, did you find it easier to remove the front wheel or leave it on?

[fly300kts]

Did not remove any of the wheel to do it. The DIY shows the wheel removed because I repaired the front axle at the same time

Phil

[womensecks]

I just did the install as well along with Quattro.

Yes, removing the front and rear wheels would make things easier, but it is not necessary assuming you have the right tools. You wont be able to screw things in properly with a standard screwdriver.

[Sonick]

I have hade the votex side skirts on my avant for one year now :

http://i248.photobucket.com/albums/gg192/geirg/009.jpg?t=1271619970

[Sharkfin]

^looks great, I plan on getting s4 door blades as well

[Tusin]

Still think S4 blades + the skirts looks goofy (hence I sold my blades). But to each their own:)

[rensho]

Still think S4 blades + the skirts looks goofy (hence I sold my blades). But to each their own:)
+1

[europaisch]

+2

[fly300kts]

Once I have installed the rear DTM bumper, I will post close up pics. I have the S-line blades.

Phil

[CleverA4Name]

Finished my install yesterday and it went great. Phil's DIY was excellent ** thanks again Phil! I will post up pictures this week.

[volcomic]

Still think S4 blades + the skirts looks goofy (hence I sold my blades). But to each their own:)

+4. Only the non-sline/DTM door blades look right with the DTM skirts IMO. The S-line blades aren't bad, but they hide some of that beautiful lip on the skirts, and make the whole bottom look too busy.

[JEENYUS]

Pictures of the car will come later...after a good bath [:D]
Let me know if any question

Phil

takes you a long time to take pictures...

thanks for this write-up. also, how much did you pay to get the DTM sideskirts painted?

[fly300kts]

takes you a long time to take pictures...

thanks for this write-up. also, how much did you pay to get the DTM sideskirts painted?

For the pics, I am just waiting to paint and install the rear DTM bumper
As far as paint cost = nada
I just bought the base and clear. I then prep and paint the parts myself, I have access to a paint booth where I work

Phil

[xULx]

Phil,

Move to San Diego. You need an apprentice.

[fly300kts]

Phil,

Move to San Diego. You need an apprentice.

[:D]
Kidding aside, I am going to Diego for my business quite often

Phil

[xULx]

Appears like you found a side job on your business trips $$$

[fly300kts]

I will PM you as soon as my next trip is scheduled

Phil

[xULx]

Ill be waiting, now get that bumper on, peoples obsession depends on it.

[fly300kts]

I will Jesse.
Still need to finish the sanding. Might be able to shoot the paint this WE

Phil

[Sharkfin]

I got my side skirts painted over the weekend and they cost me $210.

[xULx]

Nate,

I was quoted about that per skirt at my usual paint shop, they have done fantastic work restoring my paint for low cost, but I feel 400 ish is a little much. Dangit

[Sharkfin]

It is, I got the bumper and skirts for $490. Picked them up today

[JEENYUS]

490 doesnt seem to bad. i have yet to be quoted. i think i might go the spray can route as Audi sells (from the dealer) color matched paint to VIN for 15.00 plus it comes with a clear coat. :)

[Sharkfin]

Actually 490 is a very good deal, I talked to 4 shops and they all wanted 400 for the bumper and 250+ for the side skirts. (btw these are with no install and already primed)

And if you use the touch up paint to paint an entire skirts, good luck getting it even

[fly300kts]

490 doesnt seem to bad. i have yet to be quoted. i think i might go the spray can route as Audi sells (from the dealer) color matched paint to VIN for 15.00 plus it comes with a clear coat. :)

I hope you are kidding [o_o]

Phil

[Sharkfin]

Seriously, I'm glad you agree there phil- dumb ass idea

[europaisch]

Hey Phil,

Just wanted to say thanks for the suggestion on replacing the double sided sticky tape. I second that.

The OEM stuff is not very tacky and relatively brittle. The new tape covers more surface area, has fresh tack, and is very easy to work with.

Heads up to others doing the DIY; refresh the double sided tape. It makes a world of difference in longterm durability. Supposedly it's the best stuff on the market right now. It's a real chore to remove the old stuff, but worth it.

Also, Audi instructions dictate that you not "put a mechanical load" meaning drive for 24 hours. Also not to wash for 48 hours. During that time the new skirts are to be Masking taped up to the closed doors. Basically making your car undriveable for 24-48 hours. That is what Audi recommends. We just taped four spots on the skirts from the bottom up on to the door sill for good measure.. Doors still useable. Half Audi directions but driveable too.

I drove my car 60 highway miles home averaging speeds of 80+. My skirts are solid. I'm gonna drive minimally over the next 24 hours if I can. And not wash for 48.

In short, the tape is a great and mandatory suggestion. Thanks again.

And I have the S-line blades but prefer the flat blades. Any Ibis wanna trade?

http://i63.photobucket.com/albums/h157/grouchfactorzero/82fcd4f7.jpg

[spockb7]

Nice write up as always.

[fly300kts]

Hey Phil,

Just wanted to say thanks for the suggestion on replacing the double sided sticky tape. I second that.

The OEM stuff is not very tacky and relatively brittle. The new tape covers more surface area, has fresh tack, and is very easy to work with.

Heads up to others doing the DIY; refresh the double sided tape. It makes a world of difference in longterm durability. Supposedly it's the best stuff on the market right now. It's a real chore to remove the old stuff, but worth it.

Also, Audi instructions dictate that you not "put a mechanical load" meaning drive for 24 hours. Also not to wash for 48 hours. During that time the new skirts are to be Masking taped up to the closed doors. Basically making your car undriveable for 24-48 hours. That is what Audi recommends. We just taped four spots on the skirts from the bottom up on to the door sill for good measure.. Doors still useable. Half Audi directions but driveable too.

I drove my car 60 highway miles home averaging speeds of 80+. My skirts are solid. I'm gonna drive minimally over the next 24 hours if I can. And not wash for 48.

In short, the tape is a great and mandatory suggestion. Thanks again.

And I have the S-line blades but prefer the flat blades. Any Ibis wanna trade?

http://i63.photobucket.com/albums/h157/grouchfactorzero/82fcd4f7.jpg

You welcome.
Yes, replacing the tape is almost MANDATORY
I am sure that a lot of people will be candidate to trade your blades but to be honest, I like the look with the S-line blade while the S4 blade would not work

Phil

[Sharkfin]

I'm hoping I like the flat blades because then it saves me $400 or s4 ones....

[ECS Tuning-Audi]

Wow you guys went to town in here over the last couple of days! Nice work on the respray and mount, lines look very good from that picture. I'm a fan of the S-line blades though, why get rid of them?

And to quote everyone else, Phil - get on it!

[fly300kts]

I am Chris, I should spray it tonight

phil

[Sharkfin]

Since only a few people are subscribed to my bio thread, here is the link:

http://www.audizine.com/forum/showthread.php?303752-Sharkfin-s-Silver-B7-A4-Progress-from-Start-to-Present-to-Future/page2

Pics of the fresh paint on the skirts and rear bumper are included

[felondnb]

Cheers for this DIY Phil [:)]

Fitted the Votex skirts to my S-Line today with the help of a friend. Pretty easy all in all but I'd been given two mounting kits so we got a bit confused with twice as many bits! Pleased with how they turned out. Very subtle but helps the contour flow from the bumpers front to back. Total cost was around £220 including the skirts, paint, etc.

[fly300kts]

Your welcome Man

Phil

[daveman]

Can more people post pics of their skirts on? I have the skirts, but still undecided on the blades. I might get some non s-line ones but not sure yet.

Also, anyone have the part #s for non s-line blades?

Cheers

[ECS Tuning-Audi]

Can more people post pics of their skirts on? I have the skirts, but still undecided on the blades. I might get some non s-line ones but not sure yet.

Also, anyone have the part #s for non s-line blades?

Cheers

Click here for all four part numbers on the stock lower blades (http://www.ecstuning.com/Audi-B7_A4-Quattro-2.0T/Search/8e0853959e7dl+8e0853960e7dl+8e0853969e7dl+8e085397 0e7dl/?salesrep=CArmbruster&utm_source=audizine&utm_medium=forum&utm_content=CArmbruster&utm_campaign=postreply). From top to bottom: Left front, right front, left rear and right rear respectively.

[Sharkfin]

I finally got mine installed today, took about an hour per side using this DIY. Thanks again Phil. My old skirts were really destroyed, I just threw them out.

Here are some pics:

http://img696.imageshack.us/img696/1562/img00153201005271522.jpg

http://img514.imageshack.us/img514/6889/img00152201005271522.jpg

http://img192.imageshack.us/img192/3817/img00154201005271522.jpg

http://img690.imageshack.us/img690/3531/img00155201005271524.jpg

Stuff I noted while doing the install in 80 degree weather:
-Realize you lose the weather stripping in the door jams
-The skirt is a tad less secure than the non-sline because you lose several bolts on each side
-Looks much cleaner now though
-Now you have better openings for the jack points on the pinch welds

[Mtepete]

do you guys think these skirts would look good on a stock non sline? i messed up my skirts on a curb so im toying with the idea of getting these ..

[Sharkfin]

For this price why wouldn't you get them? They would look good on anything imo. Might be sold out now though in the US...

[Mordaine]

i need to get mine done as well. the last owner used the jack on it and rubbed it into my side skirt and made a nice dig in it.....so its upsetting.

[felondnb]

do you guys think these skirts would look good on a stock non sline? i messed up my skirts on a curb so im toying with the idea of getting these ..

might as well - they're quite subtle so won't look too out of place with non S-Line bumpers [:)]

[CleverA4Name]

I have them on my non-sline and I think they look great. I plan on going DTM front and rear in the future, but for now I think they look good.

http://img693.imageshack.us/img693/7039/img2861d.jpg
http://img522.imageshack.us/img522/75/img2865u.jpg

[ECS Tuning-Audi]

For this price why wouldn't you get them? They would look good on anything imo. Might be sold out now though in the US...

We have a very limited number available at this link (http://www.ecstuning.com/Audi-B7_A4-Quattro-2.0T/Exterior/Body/Votex_Parts/ES4544/?salesrep=CArmbruster&utm_source=audizine&utm_medium=forum&utm_content=CArmbruster&utm_campaign=postreply). I do no think these are reorder-able ever again, so if you want a set I would get on it sooner than later. I can count the number of sets left we have on my hands.

[Mtepete]

dammit chris... im such a sucker for "running out, you better get them soon" talk. just ordered them

[ECS Tuning-Audi]

dammit chris... im such a sucker for "running out, you better get them soon" talk. just ordered them

I know, I hate when I say it but I'm 99% sure that we have the last few sets still in stock in the nation.

[A4Grocerygetter]

Thanks Chris for your help. Just got the skirts in a few days ago and its at the paint shop now. Will install in a few weeks as the car is going in for some cosmetic work. I'll post pics of the Avant when its done.

[beantown]

I know, I hate when I say it but I'm 99% sure that we have the last few sets still in stock in the nation.

Chris, are they still in stock?

[beantown]

Never mind, found them on your site, ordered a set.

[ECS Tuning-Audi]

Chris, are they still in stock?

For future readers, yes still in stock - click here for B7 Votex Side Skirts (http://www.ecstuning.com/Audi-B7_A4-Quattro-2.0T/Exterior/Body/Votex_Parts/?salesrep=CArmbruster&utm_source=audizine&utm_medium=forum&utm_content=CArmbruster&utm_campaign=postreply)
http://c1552172.cdn.cloudfiles.rackspacecloud.com/71458_x300.jpg (http://www.ecstuning.com/Audi-B7_A4-Quattro-2.0T/Exterior/Body/Votex_Parts/?salesrep=CArmbruster&utm_source=audizine&utm_medium=forum&utm_content=CArmbruster&utm_campaign=postreply)

Can almost count them on 1 hand now...

[/\G]

You have one less in stock! Ordered. Thanks for the revised shipping amount.

Just to add to the door blade question. I think they look nice with unpainted blades as seen on the ECS car. The contrast makes it look good. Everything painted looks too busy.