PDA

View Full Version : R.A.I. B5/B6 Test Pipe Sale!



Sales@RAI
06-23-2009, 11:17 AM
http://www.raimotorsport.com/v/vspfiles/photos/RAI-ACD-0001-2.jpg

With the big success with our R.A.I. test pipe, we are offering free shipping for the next two weeks, and an extra $25 off for local customers who wish to get the pipe installed here at the shop.

*ORDER HERE* http://www.raimotorsport.com/B5-B6-Audi-A4-Cat-Delete-Pipe-p/rai-acd-0001.htm

We really went above and beyond to make sure we had the most quality test pipe available. Here are a few specs on the pipe:

- The only test pipe with a 304SS "J-pipe" to prevent the dreaded CEL
- Made out of quality 3" 304.065 Stainless Steel
- Uses studs on the bottom flange, to make installation much easier than the traditional nut and bolt setup
- We have our flanges CNC'd for us for us with 316L Stainless Steel. We do not use Mild steel, so there is NEVER rusting.
- Kits come with all necessary bolts for installation. We also chose to upgrade to copper bolts to ensure longevity
- All products are also manufactured in the USA

http://i663.photobucket.com/albums/uu360/RAImotorsport/IMG_0014.jpg?t=1245774704

http://i663.photobucket.com/albums/uu360/RAImotorsport/IMG_0013.jpg?t=1245774747

Our welder has been doing Audi/VW fabrication for over 12 years and makes sure every Test Pipe we sell holds the same quality.

http://i663.photobucket.com/albums/uu360/RAImotorsport/IMG_0021.jpg?t=1245777343

I'm at the shop from 10-7 every day, so give me a call if you have any questions (443)242-6436, or shoot me an E-mail at Clint@RAImotorsport.com. I look forward to talking to you [up].

Jake39454
06-23-2009, 11:19 AM
304 16 gauge ftw! That's what we use on everything after the turbine outlet as well [up]

Sales@RAI
06-23-2009, 11:20 AM
thanks Jake

SykoraA4
06-23-2009, 01:17 PM
awesome, im local too. so your telling me it'd be 150 with install?

biketsai
06-23-2009, 02:17 PM
That J-pipe looks awesome! I wonder if it will work on a 2001 A4.

audiluxary
06-23-2009, 02:25 PM
^^
I wonder if this will work on the 01? What is the percentage rate of not seing a cell? I will be local too in about 12 days.

J Ozzie
06-23-2009, 02:59 PM
also curious if this works on an o1 to me looks like the J is facing thw wrong way and if it is down there its gonna be stupid hard to get that 02 sensor in there. its already hard where the lower one is ne ways.

Don Supreme
06-23-2009, 03:33 PM
^^
I wonder if this will work on the 01? What is the percentage rate of not seing a cell? I will be local too in about 12 days.

As far I know this product was thoroughly tested on a B6, which is similar to an 01, ECU wise, so it should work fine.

Sales@RAI
06-23-2009, 06:45 PM
Sorry to get back on here so late, this pipe works fine on the 01s. It was tested on both a B5 and B6. I think you may be looking at the pipe from the wrong angle. The side with the studs goes to the catback, and the other side connects to the turbo.

biketsai
06-23-2009, 06:51 PM
Hmm, I mean because its almost inevitable for the 2001's to get the CEL. Id like to see someone with an 01 buy this. Not trying to put your product down, but I REALLY would like to see it work since nothing other than "coding out" has worked.

Sales@RAI
06-23-2009, 07:34 PM
Well your 2001 has essentially the same motor/ECU setup as the B6s in terms of the Wideband, 06A Block, small port head, and MAP sensor. The pipe has not thrown codes on any B6, so I would assume your 2001 would work too.

Also, we do offer the Unitronic flashes that write out the CEL even without the pipe. We do bench flashing here so we can have same day turnaround if you ship your ECU to us.

Sales@RAI
06-24-2009, 08:51 AM
bump!

SmellMyFace18t
06-24-2009, 10:15 AM
yeah Ian does awsome work he used to work at vw/audi shop in westminster...i've known him for a while great guy. see you a H2O fellas!!!!

Sales@RAI
06-24-2009, 04:41 PM
Look forward to seeing you there [up]

Sales@RAI
06-25-2009, 09:41 AM
up

mysman
06-25-2009, 12:21 PM
any reason you're making the pipe in two sections? just seems like an extra weld to crack apart.

Sales@RAI
06-29-2009, 01:09 PM
any reason you're making the pipe in two sections? just seems like an extra weld to crack apart.

Yes, just for the simple reason that we would have to get it mandrel bent and we decided not to do that. The welds are outstanding quality and will not crack [up]

Sales@RAI
07-03-2009, 06:12 PM
Just wanted to remind everyone Monday is the last day of the sale! Hope everyone has a great July 4th weekend!