dude I swear, to bad you didn't pick up a new B5 each time you decided to "tear" into your car! Cause then you'd have 3 sweet ass B5s after this winter lol.
Carbon Dash, console.... aluminum flooring, trunk, rivits? I have experience with working with CF and molds, overlays, etc, let me know if I can help.
Update: My car is leaking oil like crazy. I can not seem to find where the leak is coming from! Its on the passanger side of the bay, below the frame rail somewhere. Turbo oil return line is ok, feed line ok, and there is no real oil around the block. Plan for tomorrow is to fill it up with oil and drive to work. Hopefully I am picking up a 98 B5 Avant tomorrow so I can get this project underway!
AZ B5 & MW Moderator: PM me with any concerns or questions
'99 Audi A4 1.8T Holset HX35W- Widebody- Matte Green -PVW 11.09
01' Golf 1.8T - The daily, GT2871R .64 externally gated, Tapp 630cc mafless tune, SB stage 3, Brute rods, ported AEB, 1mm over valves, CAT gold springs, Vmaxx, and countless other tidbits
Send me apmif you need work done in New England... Fabrication, engine builds, timing belts, brakes, ect
01' Golf 1.8T - The daily, GT2871R .64 externally gated, Tapp 630cc mafless tune, SB stage 3, Brute rods, ported AEB, 1mm over valves, CAT gold springs, Vmaxx, and countless other tidbits
Send me apmif you need work done in New England... Fabrication, engine builds, timing belts, brakes, ect
I'm not hating, the car drove great, but WOT over 12psi/4500rpms was shit... Now I know once my standalone is in that the ecu was bad, you would think eurodyne would tell you that shit, asses...
Horray for Rob having a tune lol, now have fun getting the MAF setup right lol
-Jake and my shop isDoWerk Garage
01' Golf 1.8T - The daily, GT2871R .64 externally gated, Tapp 630cc mafless tune, SB stage 3, Brute rods, ported AEB, 1mm over valves, CAT gold springs, Vmaxx, and countless other tidbits
Send me apmif you need work done in New England... Fabrication, engine builds, timing belts, brakes, ect
I agree, i have seen a good amount of tapp ecus sold which run shitty. I dont understand why he doesnt sell intakes for his setup, hed make a killing lol
BetaAlphaTau Member #40
2.0 3071r wire tucked
~Brenden
If you need any work done in CFL shoot me a pm. I do it all.
01' Golf 1.8T - The daily, GT2871R .64 externally gated, Tapp 630cc mafless tune, SB stage 3, Brute rods, ported AEB, 1mm over valves, CAT gold springs, Vmaxx, and countless other tidbits
Send me apmif you need work done in New England... Fabrication, engine builds, timing belts, brakes, ect
Whatever there is. I just figure if you're getting rid of some nice interior bits I would take them off your hands since my interior is getting long in the tooth.
BIG thanks to Jeff D and the boys at A&P for helping with everything! I have already pulled the evap system and sent toooons of parts off to powdercoat. Jeff is going to start the assembly of the internals this week. The motor should be all finished by the new year so I need to get goin on my routing and welding!
Thats all for today.
AZ B5 & MW Moderator: PM me with any concerns or questions
'99 Audi A4 1.8T Holset HX35W- Widebody- Matte Green -PVW 11.09
01' Golf 1.8T - The daily, GT2871R .64 externally gated, Tapp 630cc mafless tune, SB stage 3, Brute rods, ported AEB, 1mm over valves, CAT gold springs, Vmaxx, and countless other tidbits
Send me apmif you need work done in New England... Fabrication, engine builds, timing belts, brakes, ect
Bookmarks