View Full Version : BBS CH incoming
ant7701
06-15-2008, 05:17 PM
oK....so i'm picking up a set of CH's used and I have a few questions.
they are 19x8.5 with a 35mm offset and 5x112 bolt pattern from a merc. they should fit my S4 with NO problems right??? :)
what about future BBK???
and lastly....can I use the OEM wheel bolts or do I have to order a new set???
S-Fore
06-15-2008, 05:36 PM
Same dimensions as my Neuspeeds, so should not need new wheel bolts(although my wheels came with new bolts from Neuspeed, RAD's). With those dimensions, I have 5mm spacers in the rear and sits perfect for me, fyi.
panix73
06-15-2008, 05:53 PM
oK....so i'm picking up a set of CH's used and I have a few questions.
they are 19x8.5 with a 35mm offset and 5x112 bolt pattern from a merc. they should fit my S4 with NO problems right??? :)
what about future BBK???
and lastly....can I use the OEM wheel bolts or do I have to order a new set???
Go see Al at Al's Hupcaps (http://alshubcaps.com/) in Mineola. Honestly, he is the best guy around. He stocks just about every size bolt, yes you will need new ones. If you give him a call I'm sure he'll be able to tell you what you'll need and what tires to use for the look and fit you are looking for.
[wrench]
chrislane31
06-15-2008, 05:54 PM
Call BBS and get the bolts and PFS hub rings that you will need to run these wheels.
panix73
06-15-2008, 06:01 PM
Same dimensions as my Neuspeeds, so should not need new wheel bolts(although my wheels came with new bolts from Neuspeed, RAD's). With those dimensions, I have 5mm spacers in the rear and sits perfect for me, fyi.
Whenever your wheel offset changes, either by changing wheels or with a spacer, you should use new bolts to correct the offset change. If you do not, your bolts may be longer or in your case, shorter than needed.
Answer: Do a wheel stud conversion FTW!!
RAudi Driver
06-15-2008, 06:08 PM
Ball seat on the stock wheels and cone seat on BBS wheels. You will need new bolts!
just do what Chrislane said and get everything from BBs in one shot. It'll be easy and painless.
chrislane31
06-15-2008, 06:25 PM
And I think BBS only charges $40 for everything
Cargo8
06-15-2008, 07:44 PM
They will fit properly (same setup as my own) but you will need new bolts, as stated above. Call BBS and order them.
What size rubber are you running? The guy above who said 5mm spacers is running different tire size than myself, so depending on the rubber you may not be able to do 5 mm
2PUTT
06-15-2008, 08:06 PM
just make sure the center hubs are the same. the bolt pattern and offset should be right.
ant7701
06-15-2008, 08:18 PM
ok....anyone know how to contact BBS? couldnt I just get everything from tirerack
im asking because I didnt know if BBS directly would sell to individual customers.
and the tires are bridgestone potenza RE050 245/35/19
chrislane31
06-15-2008, 08:31 PM
just call them directly
2PUTT
06-15-2008, 08:39 PM
ok....anyone know how to contact BBS? couldnt I just get everything from tirerack
im asking because I didnt know if BBS directly would sell to individual customers.
and the tires are bridgestone potenza RE050 245/35/19
call tire rack. they sell the hardware you will need.
kloover
06-15-2008, 08:44 PM
call tire rack. they sell the hardware you will need.
2nd - Tirerack will have exactly what you need.
S-Fore
06-15-2008, 08:49 PM
http://www.radusadirect.com/
Where I got my bolts to run my spacers. I'm running the same tires, 245/35/19 Bridgestones, and my rears sit flush with the fender.